before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Using NRF2401+, I have two units running side by side on the bench.
With Auto-Ack turned OFF I can successfully read the RPD register (bit 0) and get the expected readings...
I have a small problem with Bootloader + application in our custom board.
If I do the DFU update,application starts at first time but if i do a power reset application doesn...
Hello,
Some time ago I bought an nRF51822 evaluation kit to start developing with this chip. Now I have a project that needs a small pcb like the beakon you show here www...
Hello,
I am using the following code to set time in my code, but when trying to set 2100 year or 2040 more year with nrf_cal_set_time function,
it is failed, it shows...
Is it possible to send an SMBus quick write and quick read using the TWI hardware?
The sequence is:
<START><ADDRESS><R/W><ACK><STOP>
I can send the address, but...
Hello,
if I send a byte over uart to an device (e.g. gps -logger), the same byte will printed to the terminal (e.g. Putty or Termite).
If I get a byte from the micro-controller...
I am confused from reading the nRF52832 Product Specification on how to clear the GPIOTE port event (EVENTS_PORT) register?
On Section 21.2 (Port event) on page 158, it...
I am experiencing a difference in current between the example program during advertising between a IAR compilation and a GNU compilation.
The differences appear to be significant...
Hi,
Can the Nordic SoftDevices be consumed by a BareMetal ARM GCC compiled application?
Which compiler/linker flags are needed for the application to be able to link...
Hi
I am working on a firmware which can be used in serveral custom boards. While it works perfect in old sdk, I met the following problem when migrating from Sdk 12.2 to...
Hi,
I have tho following configuration: SDK 10, S110 and I'm using Segger Embedded Studio, single banker dfu.
I am able to program DFU and buttonless DFU; However, when...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hello,
I've been using the new power profile kit and I seem to be getting only 3 volts output as opposed to the previous versions where I was getting about 3.6 volts. How...
I was checking out the serial example using two PCA10040 evaluation boards. Most of the commands were executed successfully as mentioned in the link http://infocenter.nordicsemi...
