Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
Hello, My question is when the nrf51822 connect the phone A, I whant disconnect ble on nrf51822 side let the new phone B can scan and connect nrf51822.
when used "sd_ble_gap_disconnect...
main (5).c
I have attached my main code here.Please have a look at it.I am using fs_store to write in flash location in the on_adv_report() function under the switch case...
Hello Everyone,
I am using nrf51822 with S130.
After completely erasing the chip, with the below mentioned code snippet in application code:
NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen...
Is there a way to capture and clear a timer without being interrupted. This doesn't seem possible with shortcuts. also it looks like theres no capture event with which to...
Hi,
Im using nrf52 dk of pca10040 of softdevice 132 with sdk version 11. I'm working on MPUexamples. The codes used to work few days back but now, it no longer works properly...
Hi!
I'm developing an application with a dual role on the nRF52840 PDK. On the one hand, the second nRF52840 PDK in the peripheral mode with which it is necessary to provide...
hello
i want to make one way data flow connection by using 2 nrf52832 and keil 5v
TX uart ----->BLE ----->BLE -----> RX uart
can you please help me!!
thank you...
Hello,
I am trying to compile this demo with Segger Embedded Studio but compilation always fail with the error "Cannot open file C:/nRF5_SDK_14.2.0_17b948a/examples/ble_central_and_peripheral...
Hi! i am using nRF52832 development board . i have flash the example code in development board and it is successfully flashed into nRF52832 development board. But i am not...
Hi,all.
I made observer with using ble_app_uart(central).
And, I transmit UUID with using uart.
Test result, I confirmed that the previous value of p_adv_report-...
Dear All.
I can use DTM F/W for nRF52 Device. And I can use nRFgo Studio to do Bluetooth --> Direct Test Mode.
Now, I need to do test 2.4GHz. In the Features box of...
Hello,
Is there any sample code in SDK example, to show how to use nrf51822, to both broadcast a beacon and also to listen to a beacon from another 51822. Also I am using...
Anyone done or seen current consumption measurements for the Thread SDK on nRF52840?
I need to understand relation with other technologies and other chipses on this, and...
Hi, when trying to program my nrf51822 chip, I went through the following error streaks:
1.I started to get "no device found error". Can be easily solved by turning off...
