I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hello
I am using nrf51822 .The function of DFU has worked well,but some weird problems puzzle me.
1、After DFU is successful,what is nrf51822's working state? Does it reset...
When I just plug the USB cable on the board I get a GPIO high voltage of 3V. But when I also put +5V on the external supply pins, the GPIO high voltages are 4.5 V. Is this...
Hi,
We are using nrf52832 board with sdk14.0. We are facing two issues:
Our use case is to send the data continuously when the notification is enable and stop...
The Bluetooth pairing is not working properly. I am developing the Application based on Bluetooth pairing with UART. Here I have included my concept and Program.Help me out...
Hi to everyone!
I have been getting the output of NRF_LOG_INFO functions through RTT in J-Link RTT Viewer terminal. The code has been executing in nRF52832DK.
Now I...
I have set up an nrf cloud and can control the led on pca10056 using the nrfcloud so configuring the gpio(pin no 7(Port P0.7))is becoming a problem.Can u provide me with a...
Hello,
I bought a nordic/wellcore ibeacon (nrf51822) to experiment. I want to enable all the features and would like to know what value to assign to the temparature enable...
Hello, i am using SDK12.2.0 and SD s130 on a nRF51822 (AC) and i am trying to add an external interrupt on a pin in the cscs ble_peripheral example. The code i am using (and...
Hi
We are using sdk version 12.2.0 and trying to change it to sdk 14.0.0. However, when I measured the power while converting the code, ppk confirmed that the sdk 14.0...
Hi all,
I'm using SD S132 v5.0.0 with SDK 14.0.
I'm testing now the BL buttonless DFU (and later the SD buttonless DFU) after working well with the app buttonless DFU...
I've implemented monitor mode debugging as described here and it works great. When I get a hard fault, it doesn't break in the IDE anymore. So it appears to be running fine...
I can connect the kit to the nrf cloud and even add the device to the gateway but i cannot switch on and off the leds.Where is the source code for the nrfcloud example?I cannot...
Hi all,
I recently encounter this strange issue that I couldn't understand. My code works perfectly fine during debugging on all 52832 chips, but freezes without response...
For nrf52832, I use pstorage to set 254 blocks with 20 byte of each block, that will use near 5 pages.
now I fail to clear data all block together. pstorage_clear( &block_base_handle...
