Hi,
We are currently in the research and development phase for a new line of IoT devices designed to work over the Matter protocol. After thorough evaluation, we found the...
Hi,
I started the LBS example on the nRF52DK_52832 kit and connected the PPK2 kit to the P22 pins for measuring power consumption. I am not sure if I did something wrong...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I am utilizing the nRF52832 with softdevice S332 with both ANT and BLE enabled (no peer manager). When I set the ANT search for a channel to use ANT_WAVEFORM_FAST it causes...
Hi,
I am trying to use fds file system to save some data in flash,
when using the example code of sdk 14.0.1, it is not normally operated,
NRF_ERROR_INVALID_PARAM error...
Hello
I am using nRF51822 Nordic controller, SDK 9 and S130 Soft-Device.
I have used to generate a 1 KHz PWM signal successfully using timer 1.
And generating a 4 MHz...
Hi,
I have designed one custom board using nrf52810 and GPS module. where i can get the gps data via UART to my nrf52810 chip and then from nrf52810 sending same data to...
Hello Sir,
we have designed custom PCB using nRF52832, I am little confused for is it OK. I have attached top and bottom layer layout of my PCB please sir review it and...
Hi guys,
I'm struggling over some basic concepts related to the Mesh SDK, specifically with the Bearer layer and why the Mesh SDK uses the Timeslot API. I'll try to explain...
Hi all,
I'm trying to writing a device information service client on top of ble_app_multilink_central example on nRF52830 using SDK14.1.0 and softdevice 5.0 and have a...
Hello World,
I checked the Developers Zone, but I have not found the direct example of my problem.
I use the RuuviTag board with NRF52832_XXAA.
I use it as a development...
Hello,
I have question about signal names in datasheet nRF52840.
On the pins B19 and T2 on page 14 both pins have the same initial signal names (P0.11).
Please send me...
Hello,
I would like to add the ST7735 driver from the nRF5_SDK to the Mesh SDK along with the necessary components (SPI,..). I copied the entire components directory to...
How is the health model supposed to work?
I'm currently doing some tests with the light switch example and I don't really understand the different roles of the nodes in the...
Hello,
I have some trouble to write/read data in flash region,
I am using FICR region to save data,
if trying the command : nrfjprog --memrd 0x10000010 --n 0x10
I...
Hello All
I am using an SOC which has nrf51822. I am trying the blinky example with the softdevice. When I debug the code, the code first enters the SystemInit function...
Hello Nordic devzone,
I'm using Mesh SDK and nrf52PDK, and i'm using light_switch example.
could you please let me know that if it is possible to broadcast a message from...
Hi Experts:
I met one complier error as blow. Would you get me some idea? High appreciate!
--------------------------------------------------------
Ubuntu 16 (64 bit...
