I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
I have one pca10040 board, I want to realize the data transfer between the nrf52832 and the PC by BlueTooth, I use python3.5+PyBluez. When the nrf52832 is running the "ble_app_blinky...
The following lines are copied from the SDK15.0 documentation:
<pre>
Supported boards:
- PCA10040
- PCA10040E (nRF52810 emulation on PCA10040)
- PCA10056
- PCA10059 (support...
Hi, we are using
'iOSDFULibrary' , '~> 3.0' for firmware updation process. we are getting "DFU not found" error when device is already in dfu mode at the time of update...
Hello,
I've got the light_switch example running. I would like to extend this example with the possibility to send a broadcast messages from every node, the light client...
Hi, We are facing issue with updating firmware using NordicSemiconductor/IOS-Pods-DFU-Library. we are unable to upload new firmware and getting failed operation at the time...
Hi,
although the NRF52840 has a nominal receiver sensitivity of -103 dbm I am only able to get a sensitivity of around -97 dbm. I know there was a bug in older soft device...
Hi all,
im using keil5 for this .i getting problem or may be confusion while selecting the packages .also could i use the softdevice for this .Also wanted to know the uart...
I want use two 52DK for BLE transfer demo, one 52DK download nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart",
other 52DK download "nRF5_SDK_15.0.0_a53641a...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device. Schematics are shown below
here BATTERY is connected...
The nordic thingy won't program anymore every time I try to program it gives an unknown error.
Does this mean that it is bricked and i need to change the chip or is there...
hi,
I am trying to develope a code to blink 2 LED's for different time interval of 500mS and 800mS using TIMER but I want to control them using TIMER 0 for one LED and TIMER...
Good afternoon,
I would like to ask you if it is actually possible for the peripheral device to automatically repair with the central device after being powered off through...
Hi All,
I have an application successfully running on nrf52832 with sd132 which I am migrating to nrf52810 sd112. Unfortunately since the softdevice structure has changed...
