Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi I try to use "light_switch demo" , but sometimes the server does not connect to client, yesterday they could connect , but today they will not and I have not changed anything...
Are sd_flash events NRF_EVT_FLASH_OPERATION_SUCCESS and NRF_EVT_FLASH_OPERATION_ERROR actual events, schedule and only run when app_sched_execute is run. Or are they run from...
How to run the sdk examples from usb on the Sparkfun. I can run the adruino code, but want to shift to a more standard production environment.
After manual install of GCC...
I can run the SAADC example and read the analog inputs fine, now I've modified the code to simply read the adc with the blocking nrf_drv_saadc_sample_convert call
All I...
Dear All,
while testing an own nRF52832-based PCB and an nRF5840 PDK for current consumption, I compiled and flashed the code below to both devices. Since then I am not...
Hello All,
I don't find any example of Dynamic Multiprotocol of ESB and BLE.
The current multiprotocol example in Nordic’s nRF5 SDK is a switching solution for multiprotocol...
Hello,
Here is a summary of my main transmission protocol:
The (unique) client contact one of the many servers to get the value of a particular server's state.
In the...
hellow nordic.
i use sdk14.2 ,but pstorage_update return NRF_ERROR_NO_MEM.
i use NRF_SDH_SOC_OBSERVER(m_soc_evt_observer, 0, sys_evt_dispatch, NULL) to creat sys_evt_dispatch...
I have a couple of "cannot-be-resolved" issue with Eclipse.
Issue 1:
Sometime when I set up a project in Eclipse, it runs into an issue where types like uint32_t or...
Hi,
I'm trying to send sensor data via BLE to Processing. If someone has already done it, could you post your code or help me explaining how to approach the problem?
I...
Our Nrf51822 will disconnect the connection with timeout reason when it is sending a large amount of data (about 20-70 KB) to our central device which is TI cc2540 . This...
Hi Nordic.
I have questions about preserving device unique information such as device id and so on. (The information will be written in factory)
I know the best way is...
I am trying to add I2C/TWI bus to nrf51822 device. I have used the SDK example code (12.3.0) and keep getting the following errors:
sdk/drivers/nrf_twim.h:69:38: error:...
Hi, Is it possible to make the same nRF52832 device to function as a master for some interval and then switch it to slave?? i.e, Does Nordic have a single SoftDevice capable...
