Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I'm currently trying to update data periodically in the advertising response packet. After successfully initializing and starting advertising, I configure srdata within a...
What is the difference between setting a pin output (to drive an LED) with this set of commands:
nrf_gpio_cfg_output(5);
nrf_gpio_pins_set(5);
and this set of commands...
i use sdk14.2 52832 i use uart
UART0_CONFIG_USE_EASY_DMA =1 consumption ~2.1mA
UART0_CONFIG_USE_EASY_DMA =0 consumption ~650uA
Is this a normal phenomenon, is it true...
Hello !
I'm Omar Rosas from Newark / Farnell tech Support.
I have a customer that he need's to know if there is a enclouser or housing for this part number NRF51822...
Hello,
Few days ago our CI builds which were written with Mesh SDK 1.0.0 started failing and it turns out that 1.0.0 was removed from https://www.nordicsemi.com/eng/nordic...
What is the ID for indicating that NO SD is required in a DFU pkg?
I am using SDK15 with a secure UART bootloader, but NO soft device. (just MBR, APP, BL & BL settings)...
Hi there,
we are currently designing an NFC antenna for our product based on the NRF52840.
The integration guide out of the spec is pretty comprehensive (see below)...
Hello everyone,
I would like to update my advertising data on the fly but actually it doesn't work. Some posts talk about this behaviour but no real answers.
Here's my...
Hi everyone.
In our products I am using the dfu bootloader included in the SDK 10 with very minor modifications affecting only what is advertised. Within the bootloader...
Hello!
I am trying to implement the Cycling Power from https://devzone.nordicsemi.com/f/nordic-q-a/9169/cycling-power-service-0x1818
Please, could you show how we need...
Sorry I am reposting this issue as by mistake I closed my previous question.
Hi, I have following issue and need some help. I am using SEGGER Embedded studio for ARM Release...
I used the command
nrfjprog -f NRF52 --program light_switch_proxy_client_nrf52832_xxAA_s132_6.0.0.hex –-chiperase
to programm the nrf52832 board and get the below...
Hello,
I found the strange phenomena on nRF52832.
By using the SAADC, I have some noise on ADC Data only at a certain temperature range.
Temperature range is depend...
Without FreeRTOS usbd working normaly with config:
#define NRF_SDH_DISPATCH_MODEL 0 #define APP_SCHEDULER_ENABLED 1
But with FreeRTOS need use
#define NRF_SDH_DISPATCH_MODEL...
