Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am using clock signal from external RTC chip to clock NRF52832 at 32768 Hz through XL1 leaving XL2 floating. I have verified the waveform by the oscilloscope and set SRC...
2.4g ble work in 2 mode(not same time) when reset.
when I init 2.4g clock
void esb_clocks_start( void )
{
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
NRF_CLOCK->TASKS_HFCLKSTART...
Hello everyone!
I have peripheral device with notify characteristic with 20 bytes length of value and connection time interval - 7.5 ms. So, I want to increase throughput...
Hi,
from the nRF52840's datasheet: Up to 4x SPI masters/3x SPI slaves with EasyDMA .
Is it possible to connect the nRF52840 as a slave with another microcontroller and simultaneously...
Hello,
do I need to do anything to accept new Connection Parameters as a Peripheral when the Central updates them?
I am seeing 'BLE_GAP_EVT_CONN_PARAM_UPDATE' events,...
Hi, guys.
I am meeting a terrible problem when using the SDK14.2 -> BLE\nRF5_SDK_14.2.0_17b948a1\examples\ble_central_and_peripheral
experimental\ble_app_hrs_rscs_relay...
HI,
I am using nrf52 with other mcu and sending scanned beacon to that mcu.
I have set baud rate to 921600 and transmitting data when mcu request.
when mcu request...
Hi,
We am using sdk 12.2.2 and nrf52. We are observing some strange behavior of chip. We have our own customized board.
The issue is mac address shown is different in...
Hi there,
I'm using a PCA10040 board, and the app that I am working on was originally built in SDK 11.0. I'm trying to send a stream of arbitrary bytes over USB using the...
Hello.
I am trying to download a program, but I get this error.
Beacon does not work when downloading in order of Application -> SoftDevice as indicated by the error...
Hello,
In the blinky project, I have added the following peripherals to build up an application
Timer
UART
SAADC
PPI
I have followed the saadc peripheral...
Hi, I want to use the components directory that comes with the SDK as much as possible isntead of the "packs" which comes with keil.
This is what I've selected in a project...
i have two tablets and one peripheral.Now with the code i have i connect to only one device .if i want to connect to same peripheral with another tablet i have to remove the...
Hello:
I have used the nrf52832 .when the radio have get a packet and disable the radio.I find the "NRF_RADIO->CRCSTATUS" register is "1" ,why?how "NRF_RADIO->CRCSTATUS"...
I am developing a BLE remote which will work with Android and iOS(as a remote shutter for camera). I used nRF's HID keyboard example as a base but it does not have volume...
