hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I connected to nRF51422 and nRF52823 by mesh SDK.
now I want to connect with nRF51822.
is there mesh SDK for nRF51822?
if not, which code in nRF51422 should...
Hello everyone~
I need to use 2 UARTs to connect to different chips. If I use nRF82832, can I use 2 GPIO pins to simulate another UART? I just use it for one byte or two...
Does the nRF52810 have a wake on low power comparator from OFF mode?
This is a feature that exists on nRF51822, but I cannot seem to see it in the nRF52810 as a feature...
Often, I create and download Macros and the 'play' icon is in the lead-line of the macro but after import to nRF Connect, the macro cannot be played and is NOT blue but rather...
Hello,
I am using sdk12.2 and nrf52. I want to send more than 8 packets of data to nrf app. How can I do that?
My code snippet is as follows:
enter code here
void...
Log-2018-01-12-11-49.txt When I use the nrf connect app to connect my device, it often does not connect to my device.And i see the error on the log is： ERROR 22 GATT_CONN_TERMINATE_LOCAL_HOST...
I have learned that the "sd_power_dcdc_mode_set ()" function does the appropriate mode switch.(LDO and DCDC)
I learned from the following URL.
devzone.nordicsemi.com...
Hi to everyone!
It's the first time I use and program clocks in a device. I'm very lost with crystals, power management and this stuff.
I have a custom board with two...
I am trying to flash custom firmware to Thingy using nrf52dk and nrfgostudio.
I have attached a cable from the debug out port on the DK to Thingy, and followed the steps...
Hello,
I'm using the nRF51822 QFAA and I just came out to this problem:
Is this still unsolved? I always end up in the same forum threads and making 0 progress on how...
About the PCB antenna layout of nRF52810, can i directly copy the reference layout provided by Nordic and paste it on my PCB?
Below PCB layout photo, is i directly copied...
I am about to start using the nRF52 for several projects and would like to know which version of Eclipse is recommended? Since Eclipse can be customized in many ways I'm looking...
i took the original sdk 14.2.0 s132-5.0 ble-uart nus-service example for reference measurements to send data from a 52832 to an android device running nrf uart v2.0
to...
I need to add two more led pins - #10 and #30 - to that board, but I don't know what to do with LED_START and LED_STOP lines, and so far, it is difficult for me to trace any...
