Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
I know the Nordic provides timeout parameter to control advertising parameters.
If I set the ble_adv_fast_timeout to 1s, my ble-central device scanned the advertisement...
I can use standard UUIDs and successfully add a Service and several characteristics, so I think the error message above is a red herring. When I attempt to create a custom...
Hi there,
I am trying to modify flashwrtire peripheral example code for uart bootloader,
- I have used flash read write softdevice functions (sd_flash_read/sd_flash_write...
I am trying to program a BMD-300 over a serial connection through the RigDFU bootloader. The module has been updated to the latest factory image.
I can compile the application...
Now I want to run the python scripts interactive_pyaci.py in Embedded system device, I want to know which version of Python Environment must be install in the Embedded device...
I cannot find the call to sd_ble_gap_appearance_set(...) function in the ble_app_blinky example, so that I think it's unnecessary to call:
in nRF5_SDK_for_Thread_v0.11...
Hi!
I am using UART in NRF52832 with SDK15.0.0 to communicate with TCP socket via cellular modem.
I am using printf() to send the following AT command sequence to the...
Hi, I am using the Serial port library in SDK15. I am using the port in NRF_SERIAL_MODE_IRQ mode. After transmission the number of bytes receive are variable ranging from...
Hello. Im working with:
sdk14.2
softdevie ANT_s332_nrf52_5.0.0
chip: nrf52832
Problem: we have a product almost ready to be sold. We decided to start the migration...
Hello. I am trying using the nRF52832 with SoftDevice S132 v4.0.2 and SDK v13.0.0 along with the uECC.c/h files that I downloaded from github.com/.../micro-ecc . My device...
I know you can configure the threshold for low voltage that would stop writing to flash.
some people set this to 2.7 volts.
I want to know what the minimum voltage the...
I have followed the exact steps mentioned here http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v2.0.1%2Fmd_scripts_interactive_pyaci_doc_demo_configuration...
Hi all
I use nRf52840 with SDK 15.0. It allows SPI SPIS and TWI (i2c) ,but almost 3 items in the same time. I want to use spi0 as master to configurate my other mcu and...
