Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello,
Some time ago I bought an nRF51822 evaluation kit to start developing with this chip. Now I have a project that needs a small pcb like the beakon you show here www...
Hello,
I am using the following code to set time in my code, but when trying to set 2100 year or 2040 more year with nrf_cal_set_time function,
it is failed, it shows...
Is it possible to send an SMBus quick write and quick read using the TWI hardware?
The sequence is:
<START><ADDRESS><R/W><ACK><STOP>
I can send the address, but...
Hello,
if I send a byte over uart to an device (e.g. gps -logger), the same byte will printed to the terminal (e.g. Putty or Termite).
If I get a byte from the micro-controller...
I am confused from reading the nRF52832 Product Specification on how to clear the GPIOTE port event (EVENTS_PORT) register?
On Section 21.2 (Port event) on page 158, it...
I am experiencing a difference in current between the example program during advertising between a IAR compilation and a GNU compilation.
The differences appear to be significant...
Hi,
Can the Nordic SoftDevices be consumed by a BareMetal ARM GCC compiled application?
Which compiler/linker flags are needed for the application to be able to link...
Hi
I am working on a firmware which can be used in serveral custom boards. While it works perfect in old sdk, I met the following problem when migrating from Sdk 12.2 to...
Hi,
I have tho following configuration: SDK 10, S110 and I'm using Segger Embedded Studio, single banker dfu.
I am able to program DFU and buttonless DFU; However, when...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hello,
I've been using the new power profile kit and I seem to be getting only 3 volts output as opposed to the previous versions where I was getting about 3.6 volts. How...
I was checking out the serial example using two PCA10040 evaluation boards. Most of the commands were executed successfully as mentioned in the link http://infocenter.nordicsemi...
Hi,
I'm developing a node based on the nRF52840-QIAA rev. B.
I'm using Eclipse Neon and GCC-toolchain for coding. Softdevice is S140 5.0.0.2 alpha and SDK is V14.2.
...
Hello,
I would like to be able to sample an analog voltage signal with a sample rate of approximately 250us (4096 samples/sec). I am using the SAADC example in nRF5 SDK...
