The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
I am doing a beacon application. I am advertising sensor data. I am facing issue with advertising.
When I am powering the hardware using usb cable, my device is working...
Hi,
I am trying to interface external flash with the nrf52. I am able to read the device id. After writing to the status - configuration - bank address registers, I am...
I'm finding a good topic for my thesis which come in the next semester. Has TSCH for nRF52DK be implemented on Contiki OS? If not yet, I want to implement this. It is easily...
I try multiple pins set. My pro code is here.
But this is not clear. I want to decrease my code line. Then I tried this.
I want to know where is my mistake?
I am trying to create a TDMA based network with the nRF24LU1+. I understand that nRF51 and nRF52 have the ability to trigger the transmission of a radio packet upon timer...
I'm using an nRF52 (PRX) to communicate with with an nRF24L01+ (PTX) using ESB. As part of a pairing routine they need to switch channel and addresses. I've confirmed that...
I have been working on this for very long time but I can't figure it out, I am trying to use pc-ble-driver to connect my Ubuntu/Raspberry pi to by BT832X module over UART...
I flashed firmware into my nordic nrf52832 DVK
https://github.com/NordicSemiconductor/pc-ble-driver/blob/99b5e78f96de60ee70e749bb89b280116275fb97/hex/sd_api_v3/connectivity_1...
Hello,
I envisage to use beacon as anti-theft system:
When the beacon (inside the product to protect) will be near (2m) from the door, it will trig an alarm. So a receiver...
Hi,
I want to implement Extended Advertising for broadcasting data with LE Coded PHY on the nRF52840 Boards with Softdevice S140 v6.0.0.
For Soft Device Version S132...
This is basically a bug report/feature request, but I figured having it out in the open would be good too in case anyone else runs into this.
Hi Nordic folks,
Would...
Hi Expert,
I know how to read mac address by software ,
but I need to know how to read mac address by tool like nrfgo,
I tried nrfgo and nrfjprog but failed,would...
Hello,
when I try to update bootloader on nRF52 from SDK12.3 to SDK14.2 using DFU over BLE I get INSUFFICIENT_RESOURCES error. I think it is caused by different sizes of...
