Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/4272/sd_radio_request-performance-question
I am using the S140 softdevice and the Radio Driver ( github...
SDK:15.3.0
CHIP:52832
nrfutil:5.1.0
Python:2.7
I am using this bootloader code install folder\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart_debug...
Hi,
I am evaluating the nRF52840-DK, and wanted to know if the source code is available for the 'Sniffer' project as I can only find the hex file.
Thanks in advance.
I would like to use functions from the date_time and dk_buttons_and_leds libraries in an nRF91 application. I included the following lines in the application's prj.conf file...
Hi! I'm trying to understand from the documentation why the reset pin is unique.
What I mean by that is why is the reset pin different than assigning a GPIO to a button...
Hi
I am new to bluetooth. I have two Fanstel BT832x ( Nordic nRF52832 module with Skyworks SKY66112 power amplifier) Chips. How do iImake them talk to each other using AT...
Hello Nordic Support,
I am working on an application that logs data to SD card when disconnected from USB and appears as USB Mass Storage Class on host PC when connected...
Hi ,I use SDK 15.2 ,and example is examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay\pca10040. When I call sd_ble_gattc_primary_services_discover not...
Hi teams,
I am working on Mesh SDK 4.0.0.
I have several server nodes and single client node and all server models are publishing to All-nodes(0xFFFF).
All nodes published...
What exactly are the GPIOTE IN[n] registers?
Is the IN[n] register a function pointer of a function to call when the the input condition occurs on the associated pin? If...
Hi! I'm working on a custom board with the nRF52840 via an SWD connection, from a debug out on an nRF52840 DK.
The debugger fails to connect to one of my boards, even though...
Hi,
I have CSV file stored on an SD card (which I create via the nordic board). I want to send this via a GATT connection.
I have gotten a service with a notifiable characteristic...
Hello,
I have a Thingy91 pca20035 board (not the DK). So far, I have had success building my own modifications of the asset_tracker application by building it using SES...
I can see for the same device on Android nRFconnect that the serial number in advertising data can be seen as here -->
The same device at same time on my iphone X with...
I using nRF52832 with nRF SDK 16.0.
I tested the SPIS example in the SDK.
I want to change the SPI Clock frequency to 8Mhz and read max 255byte at once.
How to set...
