Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi.
- Is it the case that before every write to persistent storage via nrf_fstorage_write, the page written to has to be erased first (via nrf_fstorage_erase) since only...
I have used nrf51Dk with nrfPPK before some days now trying to flash nrf51DK but its not detecting any board I tried to recover but not recovering it I have already added...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) For Secure Serial bootloader in below path, I want to change Tx...
Respected sir/mam,
Our system interfaced with nRF51422 and code is developed by S310 ( path :- nRF5 SDK 9.0.0 -> examples->multiprotocol ->ble_ant_app_hrm -> pca10028->S310...
Hi Devzone!
I'm using saadc to receive the value from analog sensor.
The power consumption is quite high so I wanna set the saadc's iteration cycle to 1 hour. Once...
Hi All,
I have a problem when enabling the NFC tag t2t with the soft device S140 with 52840.
I can run the NFC example project 'nRF5_SDK_15.3.0_59ac345\examples\nfc\record_urlrecord_url...
Hello,
I tried to build the SDK ble_app_beacon example for nRF51 using SES. SES version I used is V4.12 (for Windows 64 bit) and SDK version is 12.3.0.
I closely followed...
Hello,
Background:
I am using nRF52832 with SDK 15.3, SES v4.12. I want to perform OTA updates on the application i am building but i am having issues with it. I was using...
I'm not sure how often the Cortex-M4(F) design from ARM is updated, but what is version used in Nordic nRF52810/52832 devices? I want to know what ARM documentation version...
I can successfully download an image using nrfutil dfu serial when I use a test image (compiling the bootloader with the Nordic default public key) and the application starts...
Hi,
My requirement is to validate the PCA10040 dev board with a different set of UART pins. I have tried the following steps, but as soon as I start the firmware, it crashes...
Hello, I am new to BLE development and RF design. I've been doing as much reading as I can about RF design rules for PCB's, antenna performance, etc. Yet I am still uncertain...
I am trying to get a BMX160 working over SPI. I was following this post to make this code using the SPI example from the SDK as a basis. I am using SDK 15.3 with a nRF52840...
The app is foreground -> I am very easily connected with BLE device.
The app is in the background -> I get the callback and connect with the BLE device
The app is removed...
Hello.
I'm trying to get the example bootloader Segger project (secure_bootloader_ble_s132_pca10040) running on a custom board I have that uses the nRF52832 as its core...
