Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello,
While building a custom board, I need 52832 to communicate with a modem at regular intervals, send AT commands and read modem responses. nrf_serial library in IRQ...
In the documentation for “Bootloader and DFU …” / SDK16.0.0 is written “you can use such a bootloader, for example, to switch between several applications”, but I can’t find...
I connect one central and two peripherals
Both peripherals set the connection interval to 100
Observing PA / LNA shows that one is communicating in 100ms
But the other...
Hello.
I have question about output OOB and public key.
I create my Android app for Thingy Bluetooth mesh purposes. I would like to start output OOB process (then Thingy...
Hi,
I am using the nrf_log_backend_flash in SDK15.3 with IAR 8.32 on Window10. From what I see in the release notes, no improvements were made for 16.0.
In my application...
Hi,
Good day!
Statement of porblem: We are developing appliction using nrf52832. In our application we have Capacitive touch button and capacitive wheel sensor for user...
Hi,
I am using bootloader and application based on SDK15.3.0 and SD s140_nrf52_6.1.1_softdevice.hex.
I am also using our own BLE transport layer in application to receive...
Hello, I can see in the datasheet of the NRF52840-CKAA-R that the recommanded inductor value for DCCH is 10uH +-10% (configuration no. 4). Unfortunately, we experience some...
Or may be another procedure to make a list of surrounding beacons nearby using nrf52832. We are beginners, sorry.
What do you recommend to start with?
Sdk16, 7.0.1 Softdevice...
Hi,
I have configured pin 10 (STATUS_BUTTON) on my own design board using a nRF52832 chop as follows:
I am intending to use the internal pull-up resistor to pull the...
Hi,
I'm trying to emulate a server device with pc-ble-driver-py, I recently moved from version 0.11.4 using Python 2.7.12 to version 0.14.0 using Python 3.7.4. I'm trying...
Hi,
I am using segger studio and NRF52810 for my development. I started with the NRF52 dev kit and complied with the sample app given in PCA10040e folder.
Now I want to...
Hi All,
I'm trying to figure out the best way to implement the security between two industrial IoT devices. We don't have a good out-of-band channel for more "traditional...
Hi,
I'm using Thingy:91 and I have built and flash the asset tracker software. I have connected the external GPS antenna (MIKE3A or similar), see picture.
How do I check...
I am using nrf52832 chip along with softdevice as a peripheral. There is a requirement wherein we want to encode the advertisement data.
Came across ble_advdata_encode(...
