Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I try to create coap server project and it should by updateable by DFU. I merge project simple coap server and thread dfu client, and I keep instructions in documentation...
Hello Everyone,
I am Using Nrf51822 module and s130_nrf51_2.0.1_softdevice . my actual function nrf51822 twi interface with stc3115 Gas gauge IC .read the battery voltage...
Hello,
I am implementing ble advertising using below code, i encountered a strange behaviour with this code. If jlink is connected the advertising works just fine. if I...
I have created one characteristic in which i am trying to write multiple bytes at the same time i want to use that for further processing, how to access that whole data which...
Hi,
I just started working with Nordic nRF52840 serial interfaces,can you please tell me which one is best for serial communication among SPI and I2c and why?And can you...
Hi Nordics, I know it has been asked over and over again about doing DFU of slave nrf52 using a central nrf52. devzone.nordicsemi.com/.../ota-dfu-application-firmware-by-ble...
Hi we are trying to program code using the SDK v12.3 library onto a custom NRF51822 board using SES. The custom code contains B luetooth routines, GPIO routines, and TWI routines...
PlatformIO team is pleased to announce the release of Nordic nRF51/52 development platform . This release introduces many new features and performance improvements. The notable...
Hi all,
I am trying to deploy the long range mode with nRF52840. I modified the blinky example under SK 16.0.0 and it just keeps resetting
and the error code is 0x0007...
I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
Please help me sort out one question.
I have a peripheral device that stores an archive with data. At a certain point, the archive is transferred to the central device...
Hello,
We are focussing on the nRF9160 to build a IOT datalogger.
We would like to intergrate an micro SD card.
Now, I mis the 4-bit SPI interface ( SDIO), and I asked...
Greetings,
A very bizarre thing is happening. This is the umpteenth time I'm working on a peripheral driver and the code gets stuck at 'NVIC_EnableIRQ(UARTE0_UART0_IRQn...
I would like to implement Bluetooth 5 packet exchange without the softdevice.
How can we convert the
nRF5_SDK\examples\peripheral\radio\receiver
nRF5_SDK\examples\peripheral...
How can you use assisted GPS(AGPS) in nRF9160?
Let's say you get assisted data from "supl.google.com" and how do you set this address in code?
Do you have to wait for...
