Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hello everyone.
I have made the next solution for merging softdevice into debug fw.
i 've added the next lines in ld script
MEMORY { SD_FLASH (rx) : ORIGIN = 0x00000000...
Hi,
I want to output a high & low voltage with an array, the array contains a sequence number, looks like: {0, 1, 0, 0, 0, 1, 1, 1, 1, 0, ...} , and the length of the...
I'm wanting to create and Android application that can communicate with a nrf24l01 module. Is there an android library available that will permit this? Thanks in advance!
Hello Everyone,
Consider i have 2 MCU's on board connected via UART interface, one is any ( Target ) MCU (MSP32, STM32, etc) and the other is Nordic's nRF52832 ( Host )...
Hi,
We have two nRF9160DK and both have the SIM card issue as below, and our development was blocked by this issue, so please help check it, thanks!
original case
Hi!
I am trying to figure out the app_timer_library but am running into some (to me) strange behaviour. For the first seconds it appears as if the LFCLK is running much...
Hi,
I've built a application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently the...
Hello
I successfully build asset tracking example , for nrf9160_pca10090ns
when I try to run using segger, I get the following:
SPM: NS image at 0xc000
SPM:...
Hi,
I am trying to use the Android-BLE-Library with my nRF52832 device (I do have another test Android app which can work w/o using the library).
I followed the Github...
I am porting RF evaluation code to the nRF53 NCS/zephyr/Segger Embedded Studio toolchain, using only the network core to start.
How do you recommend configuring the network...
Hi,
I am trying to install Command Line Tools on Ubuntu 16.04. But I am not able to find the download link for it. The page shows ERROR 404. Can someone direct me to the...
Hello,
I am need to add voltage sampling functionality to existing FreeRTOS framework on a low-power BLE device. When I enable BLE, I get 3mA of current, which stays there...
Hi,
When I call sd_ble_gap_disconnect( m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION), it usually takes about 100 msec, and come back with event BLE_GAP_EVT_DISCONNECTED...
When not using the SWD port I would like to pull up the SWDIO and SWDCLK lines high. Does the NRF52810 have internal pull up on these two pins? If not, what value pull-ups...
