Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
We're experiencing occasional unexpected hardware watchdog resets. The watchdog is set to 10 minutes, and sometimes just 2 minutes after feeding the WDT we see a reset triggered...
Hi there,
I'm currently developing a ble mesh network for the Thingy 52. I'm accesing the temperature and humidity sensor but I need the firmware code of the Thingy 52...
Having problems bootloading my own application on my hardware. The application runs fine alone. Using SDK 16.0 and secure_bootloader/pca10056_uart example via Segger SES....
Hello,
anyone with with knowledge on how to control the gpio pins of the NRF 9160 SiP?
In my scenario, I am using P0.01 - P0.12 as digital control signals, for "Enableing...
Hi Nordic
For mesh-sdk-4.0 examples/light_switch/server, how many LPN can a server to establish friendship?
Is it limited to MESH_FRIEND_FRIENDSHIP_COUNT?
Regards...
Hi, I have custom nRF52832QFAAE1 when I tried to run Peripheral applications which are working fine. whereas BLE applications are not running it seems.
here are the things...
Hello,
When I clean a project and do a new build, parallel settings looks wring (my AMD ryzen 3900X with 12 cores never use more than 40 %).
Do someone have a setting...
Currently, we are testing the nRF52840 range evaluation using the nRF52840 EVK kit.
As of now, we are getting the only 120 to 125-meter range using 125kbps data rate @ 4dBM...
Hello.
I found in Provisioing chapter on this document: https://www.bluetooth.com/specifications/mesh-specifications/
something like list of provisioning commands: ...
Hello.
I plan to perform antenna matching to improve the performance of my design.
I would like to know any differences when performing the match on bare pcb and pcb...
Hi,
I'm working on a test for the pulse width measurement, the input is analog signal.
I'm using a while loop, and use nrfx_comp_sample in the loop to get the voltage...
Hi All,
I just start to use the Thingy 52 and I would like to know if there is any source code for development purpose for Windows. Also, which development software does...
in SDK/examples/peripheral/blinky/ hex
there is one file
blinky_pca10056 _mbr .hex
in
SDK/examples/peripheral/blinky/pca10056/ mbr /ses/Output/Release/Exe
there...
Hi
I am very new to BLE...
We are looking into a new industrial product design that will be battery powered, and be capable of communicating with BLE sensors (Mesh not...
