Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
My company has a product that is running on the nRF51, with firmware written in SDK9 and sd310. I've been tasked with developing a path to update them to SDK 12.3 and sd130...
Hello nordicsemi community. I'm trying to use the SPIS example provided in the NRF52 SDK to receive data from another SPI master running on an FPGA. I modified the code to...
Hi,
I'm trying to write data to flash as shown in example under nrf5_sdk/examples/peripheral/flash_fstorage, with identical steps.
However every time I call the nrf_fstorage_write...
HI,
I am using nrf52832 with sdk15.2.0 and softdevice s132. I face some issue related MAC address of nrf52832.
when I reset the sensor MAC address of the sensor change...
I am trying to step through the code of an example of the nRF5_SDK_16.0.0 on the nRF52 DK board.
I downloaded the latest version of Segger Embedded Studio (v4.30c) and I...
Hello,
I have a brand new Thingy 91 running the default asset tracker application connected to nrfCloud.
I wanted to build the asset_tracker myself and upload it to validate...
Hello, I just got an nrf9160dk with hopes that it would allow me to reprogram a Thingy91 that I couldn't program through the MCU method. (this is an still open ticket: https...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\experimental_lpn and board PCA10040.
When I close main.c ERROR_CHECK(sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE)), nRF Mesh...
Hello,
I'm started implementing DFU over serial port and see documentation from this link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi, I am now using nRF24lu1p, for using cklf_wdog_init() to enable watchdog, then I set cklf_wdog_init(10) in main function, but don't know how to set watchdog event handle...
So we have been developing on the nRF52811 and realized we need OTA (Over the air Frimware) aswell and we have 30kB Flash and 8kB Ram remaining. Can this be done?
Also a...
Dear Sir/Madam,
I am trying following,
1. Avoiding SPIM transfer interrupt handler.
I am performing following steps,
1. nrf_drv_spi_init() for Handler parmater 'NULL...
Hello,
I'm using nRF connect for power profiling of nRF52840 DK. First time it works.
If we close the nRF connect and open it again then I get error.(Also after power...
How can I do LESC on my central with an Android peripheral device, if with each new connection the MAC address on Andriod changed randomly?
The first time I am making a...
