Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
we are developing a firmware for the nRF52840 which requires the use of Bluetooth and the SPIS (SPI Slave) functionality.
We are using S140 & SDK 16.
We encounter...
Hi,
I'm having an issue with using nrfutil to generate a bootloader settings image for loading onto an nRF52840 MCU. The resulting image appears to have the wrong starting...
The SERIAL_OPCODE_CMD_CONFIG_TX_POWER_SET (0x44) is not supported in mesh SDK v4.0.0, so I added the following in the file serial_handler_config.c
#include "core_tx.h" #include...
Hi,
I have an application that needs 256kB of RAM however when I try to compile the code for the application processor it complains that there is only 64kB available....
Hi, I've created a custom service for my application. However, is there any way to give a name to the corresponding UUID? I want the custom UUDI to be appearing for example...
Hi,
I updated Segger Embedded Studio to the latest version, 4.50, after that it asked me to update JLINKv6.62a firmware update, but there after I had problems with the board...
Cortex M33 applications on the Thingy-91 - are we able to write any application program that would normally run on a standard M33 ARM processor (off the shelf) - or are there...
Hi I m new to Nordic products and I m just evaluating the nrf5340-PDK.
is it possible to enter in SYSTEM OFF and wake up the CPU with RTC0 or RTC1 interrupt?
How To do...
Hello to all. Is it possible to send and receive data between 52840 dongles using ZigBee? I need a simple program which records data in one dongle and sends to another. Thanks...
Hi :
Our project(SDK15.2) use the uart DFU to transfer the firmware , usually when the firmware has been transfered ,it can jump to app successfull .But Sometimes,bootloader...
My goal is based on SDK16.0.0 and s132_7.0.1 softdevice to achieve BLE DFU (requires binding) and UART DFU work at the same time, I have combined the 'secure_bootloader_uart...
I am having an issue using the DTM app in nRF Connect. It is the latest version of the app (v3.3.0 as of this writing). The issue is that if I disconnect the debug lines ...
#define FIRST_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(20000) //20s
/**< Time from initiating event (connect or start of notification) to first time sd_ble_gap_conn_param_update...
Hi,
So I am currently trying to connect my nrf52840 DK to aws cloud using an LTE modem. My aim is to be able to store responses from the modem and parse them appropriately...
I have a simple question.
I am successfully reading an external ICM module and I am trying to print is identity (value 0xEA).
NRF_LOG_INFO work perfectly well on the...
