Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I am using nRF52840 DK with SDK [nRF5_SDK_16.0.0_98a08e2]. Using example "ble_app_beacon" and i can see the result of the same in nRF connect android app.
Now i want...
Hello,
When Implementing an BLE peripheral example with some custom service and connected to the mobile phone with nRF kit. Able to connect and discover service which...
Hello, I'm workin with custom nrf52832 and sdk15.0.0, so to work with the central , i chose the example :ble_app_blinky_c . I modife the code to control my custom characteristics...
We are using regular RIGADO/U-BLOX modules (BMD300 and BMD350).
Do we need to pass PTS tests when we use Bluetooth layers (Softdevice S132_nrf52_5.1.0) with customs services...
Hello,
I'm new with ANT protocol. I read the documentation and I'm pretty comfortable with it now.
I started to develop with NRF52832 (SDK 16 and ANT stack from thisisant...
Hi there, I am a Novice in RF Board design/Antennas, particularly with nRF52 series so I have some quick questions ..
1)What are the Antenna Options for nrf52840 in mesh...
Hi,
I am using nRF52840 and nRF SDK 15.2 and nRF SDK for Mesh 3.1.
When I try to send acknowledged messages, sometimes my device needs to retry several times before the...
Hi,
I am looking for suggestions in regards to which ble example I should use. Currently, I have the hardware that writes data to a flash. I am developing the firmware...
There are several tickets from users trying to get the combination of Zephyr and Segger Embedded Studio (SES) to work on Mac OS including Catalina, but some are unresolved...
Hi,
I want to do an DFU OTA in nRF52840 BLE chip.
I have flashed mcuboot bootloader and also flashed hci_uart (To scan BLE beacons) application. This will be one time...
Hello to all,
I have a problem relating to cluster reporting: I have a device, Window Covering Device, which acts as a router and I want to connect it to Alexa, which acts...
Hello, guys.
Here they are - Thingy:91 and nRF9160-DK boards on my desk!
I was able to successfully register Thingy:91 on nRF Cloud (both SIM card + LTE modem). However...
Hello All,
I was reading about the startup code and vector table of Cortex-M4 (STm32, Tm4c123). When I tried to find out the Vector table of NRF52832 in the datasheet I...
Hi,
This is my second post about this issue, but I have not solved yet. The issue is, that I am using bpwr tx example (crank torque sensor type) with Garmin edge 520plus...
