We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
I'm compiling my project successfully in Eclipse, but trying to build it from the command line (cygwin) fails near the end with this error (make, make all, make nrf51422_xxac_s110...
I want to restart the radio portion of the softdevice - all of BLE essentially - to update the connection parameters and device name mostly. Is it necessary to re-initialize...
Hello Everyone
I have designed the schematics for my prototype but i have a question for impedance matching can anyone verify my technical doubt
I had put a 2.45GHz...
We are using nrf51822 for products of our company. We use mbed + nRF51822 driver + BLE_API for the BLE peripheral devices. The softdevice is s130 ver 1.0.0.
I create an...
Can the nRF51X22 be paired with an iPhone to communicate (both ways) using regular BLE and emit a beacon signal at the same time? In fact, I'm looking to change the beacon...
So I suspect there is a very simple answer to this, but a couple days of much reading and searching haven't led me to a very clear answer.
My setup: Galaxy S3 (Android...
I'm trying to move data over the uart characteristic. I followed the guidelines here devzone.nordicsemi.com/.../
In the main loop I am calling sd_ble_gatts_hvx until it...
I'm working with an nrf51822 with the s110 softdevice. So I'm trying to read an analog signal from multiple pins. My program will run fine for quite some time. Eventually...
Hey guys,
I need to record many time interval ?, can i generate system time and use it to record all of my time intervals?
If I want to send all of the time intervals...
The gcc compiler is gcc-arm-none-eabi-4_9-2015q2.
The make version is GNU Make 4.0 (Build for arm-unknown-linux-gnueabihf).
The error message is:
... arm-none-eabi...
So I'm using the spi_master.c from SDK 6.1 to communicate with an LCD driver. I'm using an nrf51822 with s110 softdevice. My system has been sporadically hardfaulting on me...
Hello all,
I have found closed topics here with similar names ( devzone.nordicsemi.com/.../ etc.) but my question is about adding the characteristic with encryption.
My...
Hi,
I'm trying to transition my application from SDK 7.2.0 to SDK_9.0.0 and am having some issues when including ble_advdata.h compiling with gcc:
In file included from...
Hello,
I know I'm not supposed to use TIMER1 with IRQ 0 when using a SoftDevice but I want to try anyway :) I want to do some bit banging with timing that is timing sensitive...
I am trying to program custom boards with the NRF51822 using an ARM-Flasher with no success. Using J-Flash I can connect to the device properly, program and verify the hex...
