When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I get an error sometimes in my project, and the error code is 0xDEADBEAF always. it happens often when i start advertising and connectting to a mobile phone. i get the debug...
From the nrf51 dongle User Guide, if revert back to the J-Link image from mbed image
download the latest SEGGER J-Link software from www.segger.com and open a debug session...
Hello, first of all: I do not expect support from nordic here, but if any kind sole could shed some light on this, I would be very grateful. I’m developing an open source...
Hi All,
I was tasked to create a program in visual studio that can just detect the 949-NRF51822-BEACON
Using the 949-NRF51-DONGLE. A simple application that detects the...
Hii all,
I wanted to generate a clock pulse from the pin P0.05, I've written the code and when I tested the application with nrf51 DK with chip 51422-AC its working fine...
Hey everyone,
I'm trying to send a value as a notification packet from GATT Server (slave) to GATT client (master) at 7.5 ms connection interval. I have set up the radio...
I am using a simple 4 by 4 matrixed keypad, and I would like to handle some of the decoding myself.
In essence, I would like to configure all 4 rows as low driven output...
Hello,
I already searched the forum, but I didn't find anything.
Is there a way to invert a port on a NRF51822?
I use this chip together with an XMega-Chip and they...
Hi,
I'm trying to get PCA10001 board working. I used ble_app_hrs example from SDK 6.1.0 (I'm using eclipse with gcc). The Softdevice is v7.1.0
The application seems...
I have a nRF51DK with SD 8.0 flashed.
I would like to start and stop a pwm signal with the buttons on the board(BUTTON_1 and BUTTON_2). The pwm is working fine. But when...
Hello:
I want develop my nrf51822 project base on new sdk and softdevice.In /nRF_Examples/9.0.0/ble_periphera/ble_app_uart/, the keil project device is nrf51422,and it can...
Hi,
I'm compiling the simple blinky example with no softdevice for an NRF51822 xxAA using GCC on linux. I can't get any LEDS to blink off the GPIOs, so I'm debugging with...
I can see a phrase "Not recommended " on the Evaluation Kit's page: www.nordicsemi.com/.../nRF51822-Evaluation-Kit
What could that mean for me if I already have the kit...
I found in ble_app_uart example, any device with UART app can connect to uart service and send something to COM port or just block the connection of other devices.
So can...
I'm trying to update my firmware using the dfu, I tested two examples of the SDK :
one of them is dfu_dual_bank_ble project,
I noticed that the memory allocation...
