Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
We have an odd one here. We have a single nRF51822 (QFAC) board that is acting odd. None of the other boards exhibits this behavior. They program perfectly. 3.3v supply is...
I have been having two issues (possibly related) with the RX pin of the nRF52 DK (PCA10036) using the ble_app_uart example. I have been trying to characterize the problem...
Hi all,
In my application, I take mac address of chip and make major, minor value (device 's ID) and I need mac address is a constant value. As I know, mac address is a...
because license is so expensive, I'm converting my project to OSX GNU
I'm solving problems step by step..
and there is error that I couldn't understand.
Anyone can...
Is there any way to control BLE shield 2.1 from PC rather than android / iOS app.
Also if i pass any message to BT dongle how to check the received messages.
And in...
infocenter.nordicsemi.com/index.jsp
I see a debouncing filter in the block diagram of NRF52 preview DK. Isnt debouncing implemented in software? So why need a HW debouncing...
Hi all,
I have two kinds of NRF24LE1 devices(A and B), and I want to realize that one device_A can communicate with 10 device_Bs at the same time. To explain it in detail...
I would like to use 3 PWM for controling RGBs. I use a softdevice because I want to control the pwm trough the MCP. But for now I just want to get it work to initialize these...
whether linux and bluez implemnted the simultaneous master and slave connections......?
or is it part of link layer only..?
does this feature need kernel support or not...
In the NRF51822 reference manual, the debug interface mode initiation routine is described as follow:
150 clock cycles with SWDIO=1.
I have already verified that a standard...
Hi,
I am wondering about the Cumulative crank revs for service 0x1816 & 0x1818
Cycling Cadence and Speed, Cycling Power Services
I dont understand why the crank revs...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Ok, so I've been trying to get to the bottom of a problem for a few days now where suddenly the app_timer is acting like it's on crack and running super fast, i.e. triggering...
