Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Hello everyone:
i'm testing the iot SDK 8.0, but got some problem with that.
Using the CoAP observable server example with it.
env: pca10028 + ble dongle + raspberry...
Hi,
What is the maximum rating for the nRF51's input RF level? It is not specified in the Product Specification for 51, though it is for 52.
Thanks,
Steve
By the migration of my application from nRF51 to nRF52, I can't compile the Nordic driver: nrf_delay.c
The IAR-Compiler gives that output by the build:
Error[Og010]...
Hi ,
I am using 2450bm14e0003 this instead of LNA circuit provided by NRF24L01P-R7 .Is it better to use this balun Ic or i should use the circuit provided by nordiac only...
I want to make a Bluetooth connection with nrf51422.
I am using the Keil software.
But I do not understand what the program will do the bluetooth connection.
Can you help...
I am running the Blinky code provided in nRF52 SDK examples.I am not able fix this error pointing at nrf_delay_ms. This function is hard to explain. Moreover I don't know...
To test one functionality, I am sending 1Kbyte of data to smartphone using nRF51 Uart example code.
I have tried testing with different baudrates, 9600, 115200, 38400,...
Hello,
I have an existing microprocessor application that I want to test with the nrf51822. I am currently using a different BLE chip. I do not want the trouble of porting...
I'm having a strange problem. I'm running the nRF51-DK with a dual-bank bootloader, S110 soft device, and my app under gcc. I'm using Eclipse Luna as my develpoment/debug...
When i added timer in my bluetooth code my board will not advertise.using pca10028 and nrftool box uart app on iphone 5s.
here is my complete code. Using timer1
Final with...
I'm using the 0.9.2 SDK SPI slave example to connect to a SPI master (Atmel SAM4S). When I initiate a SPI transfer from the master side I can see that all the data arrives...
Hello,
I have been going through devzone questions to figure out how to enable the default debugging messages through Putty for the ble_app_proximity example project from...
Hi:
I make the gazell ready, and I need an extern PA(RFX2401) for a long distance commuicate. But there is some trouble when enalbe the PA.
My function:
Host:
pin_Set...
Hello,
I am using ble_app_multilink_central example as a foundation of my app involving central - peripherial connection (S120 - S110). My app works nicely but i have problem...
