Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I've read through the DM code in the S110 library of v8.1, so this question is just asking for confirmation of what I'm reading.
The device_instance_allocate function returns...
I have an old version of nRFgo Studio and nrfjprog installed on my computer (version 5.2.0.45231). I use nrfjprog from command line to flash my devices (easier than clicking...
Hi, I am developing a coin cell powered NRF51-based device that needs to keep track of reasonably accurate real time (no calendar, just number of seconds) in a long term ...
hii,
i am working on ble project where i would want to read the name and address of a slave.The example i am looking at is "nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\nrf6310...
Hi All,
I am trying to make a nrf51822 talk to a SPI display by using the SPI Master.
My problem is that the display does not give any output, only takes input.
The...
Hello,
I am writing an application in Qt that runs on the computer and interacts with a nRF51422 via BLE. Now I have noticed, that I have to tell the framework, which address...
How do I reset nRF51822 to shut down the debug port?
I have a custom board with a built-in battery and strong power management.
If I power up the board without the debugger...
Hi All,
My goal is to advertise the generic packets untill a GPIO interrupt occurs. So in order to achieve low power consumption I have increased the time interval of those...
bootloader.rar (/attachment/d5fd4fbbc7d37433740f6c9468f3110b)
bootloader_dfu.rar
Hi,all.i want to set same macaddress with my app in bootloader,and advertise it in bootloader...
I have a pstorage Clear and Store that I use just before calling bootloader_app_start() in my DFU bootloader code. Everything was working great testing/compiling (GCC) under...
Hi,
we'd like to use nexus 7 II(android 5.1.1) to connect nrf51822, but cannot connect if nrf51822 uses whitelist.
step 1. we send advertising packets without using whitelist...
I'm trying to build our application using GNU Toolchain and currently facing compilation issue with __asm directive; the error thrown is:
../../NRF51_SDK_v6_1/nrf51822...
I usually see a system event "NRF_EVT_FLASH_OPERATION_ERROR" when updating my device firmware. SDK says that this event indicates that the ongoing flash operation has timed...
Hi, have anyone tested nrf51822 beacon smart kit on samsung tab 4? For some reasons it didn't detect the beacon. I have tested with company identifier of nordic, samsung and...
Since the IoT SDK is not support the IPSP Router role.
Is that mean the nRF51822 can't been used by other MCU which is running Contiki to become a Edge Router?
