RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Hi,
I want to eraze the flash page of nrf52832.
Since the default flash page size is 4096 bytes, it takes 90ms to eraze the page.
I want to shorten the time for erazing...
Hi!
I have to do an application is talk via bluetooth. I think i use codec IC to sample the voice then send data via bluetooth. In the receiver device , I use other codec...
I am attempting to write to multiple CCCD handles in a service as a central with no luck. I need to write to one CCCD handle to enable notifications and another handle (BLE_UUID_UPDATE_CHARACTERISTIC...
I am planning to start a project using nRF52832 but do not want to buy IAR or Keil as they are expensive, if I use GCC Compiler with SDK then is it possible to debug the code...
Hi, beginner here..
Frequency hopping used for advertising bluetooth beacons uses which 3 frequencies? Is it possible to choose those frequencies using the software...
I am admittedly a little lost here:
I am trying to utilize a RedBear BLE Nano 2 (nrf52832) to collect serial data from a sensor and send it to a raspberry pi every 15 minutes...
Hi, I have a wristband with a full color display and touch with a nRF51822 where I am using SDK12.3.0 and Softdevice 130. I want to display a YES or NO question on the display...
Hi Nordic,
We created a product using the nRF51822 and, because of space constraints, opted to use the antenna design from the beacon . We are now undergoing FCC testing...
I have the mesh serial example working with nRF51-DK (nRF51422). I am now trying to run the same code, via the nRF51-DK debug port, to a nRF51822 QFAC (32Mb) based board....
Hello,
I'm trying to make CLI working with UART and BLE (NUS) backend simultaneously.
Starting point is CLI example from SDK 14.
What should I enable in sdk_config.h...
I am trying to test a combination of BLE central role, Thread with CoAP server and FreeRTOS on an nRF52840 using version 0.10.0 of nRF5-SDK-for-Thread.
I don't seem able...
i couldnt find any question related to my specific problem.. when i call that function my system is resetting after a minute or so and sometimes it is shut off. i am using...
In order to connect an external sensor to the available pins, will we need to create our own version of the FW in order to communicate with the sensor? Or are there generic...
