Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
Hello,
I'm having trouble with my nRF52. The power consumption is around 2.17 mA when sleeping. I'm using the softdevice 4.0.2 enabled and using the sd_app_evt_wait and...
Hi,
I am testing the current comsumption of nRF52832 using the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon ".
The peak TX current I...
Hello,
I would like to know if I can use nRF51822 chip to get partial BLE packet information like Access Address, PDU before the whole packet has arrived.
If yes how and...
Long title, but basically sums it up - is there any way to put the nRF51 into the off state from within the hard-fault handler if the soft-device was enabled prior to the...
Hi guys, I am trying how figure out the the devzone.nordicsemi.com/.../ works or ecuations to estimate the battery life using a central module.
My central device is battery...
Hello,
I am using nrf52832 board, with SDK 11.0.0 and s132_nrf52_2.0.0. and trying to program a 512 Bytes text file using nrfjprog (J-Link: JLinkExe) in flash.
The nrfjprog...
Can anyone on the Nordic Team provide some updates on these two projects in GitHub
pc-nrfconnect-boilerplate and pc-nrfconnect-core
Are they ready to start developing...
Hello developers,
I am trying to integrate ADC, TWI based MPU6050 for accelrometer with ble_nus service for data transmission. The ADC and MPU6050 works perfect but once...
I want to use sha256 library with S130, I have checked the documentation here developer.nordicsemi.com/.../a00985.html
Its very confusing and I have no luck yet, has anyone...
Hello,
Two years ago I develop a board with a nrf51822. Right now I'm trying to use the same board again. I installed the new SDK 12.3.0, GCC ARM, nrf command line tools...
Hi all,
I'm currently trying to get the UART example (no SoftDevice) to work under Segger Embedded Studio. What I know is, that retarget.c is used to redefine the neccesary...
Hello,
I've been implementing DAC control trough SPI and DMA using the NRF52 and it is working nicely. During development however I encountered what i think is a bug in...
Hello
i am using the NRF52 EvalBoard and a ADXL362 EvalBoard. I am trying to read every 100ms the FIFO buffer of the ADXL362. Below you can see my register configuration...
I can't get NRF_LOG working with SDK12.3.0.
Using the same main.c and sdk_config.h from SDK12.2 - here NRF_LOG is working well - I get no messages in J-Link RTT Viewer with...
I have made following connection between nordic device and external sound sensor:
VCC--> 5V
GND--> GND
GATE --> Pin 04
ENVELOPE --> A0
I would like to...