My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
I have request similar to this questions but for SDK13:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
Judging by quick grep sdk_config.h from ble_app_template...
I am having some trouble getting the Power Profiler to start up correctly. Currently, I have the PPK DK plugged onto the PCA10040 DK. All of the onboard switches are set to...
Is there someone I can contact about acquiring some sample chips for prototyping? The normal distributors don't seem to have any information regarding the engineering samples...
Hello,
I am currently working on a project involving the nRF52DK to be a central device.
The peripheral device is based on the Nordic Uart service with minor changes...
hi，
i tried add ancs to the s130 ble_app_hrs_rscs_relay demo， when i use iphone5s to connect， the uart display as follow，but when i receive a message or a call， the software...
In GATT Packet transfer, is there occurs any packet loss and retrial?
I'm trying to connect about -90 Rssi dBm peripheral device with my nRF51-dk.
In this far range...
Hello,
when I was working on MSP430 I used to place the firmware version constant at a known address in flash so that it can be verified which firmware version is flashed...
I was having some troubles using the app_timer (RTC1) shortly after mesh startup, so I enabled the PIN_IN_CB and PIN_IN_TS debug pins, and saw some interesting behavior. ...
Hello all,
am trying to configure 3 adc channels in a way to have conversion in 3 differents pins, without usin timer and ppi. so I implement the following code, the problem...
Hi
May i know what would be the debugging procedure using segger-RTT for nrf52840 and what is the debugging Hardware Required ?
Thanks and Regards,
R Madhu.
I know BLE5 is the future of IoT. I also want to invest on it.
But how to setup a complete BLE5 environment? In China, IPv6 has not been supported. Therefore, 6LowPAN/Thread...
Hi,
I want to ask a few question for ble_mesh.
What do these functions do:
rbc_mesh_persistence_set(..), rbc_mesh_tx_event_set(..)
Who should do the set operation...
