Hello, I am currently developing a testing software to verify whether all the pins of my module have been properly connected. I configured pin 1.03 as a high level in the...
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
Hello,
we are testing the channel sounding performances for distance measurement with the example:
https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I'm using nRF51(822) with S130.
I registered my event handler with:
softdevice_ble_evt_handler_set(ble_evt_dispatch);
In my main loop, I call sd_app_evt_wait(); ...
Dear,all
device:51822 s110 sdk8.1.0 adverting interval:1s
or exmaple hrm s110 PCA10005
i use moto Z phone and nrf connect apk,it is difficult to receive
the advertise...
Hi, I have created a custom PCB (FR4, 4-layered) which uses nRF52832-QFAA.
This PCB uses the λ/4 printed monopole antenna .
I wish to measure the RSSI value of this...
hi,all
i use sniffer.exe(ble-sniffer_win_1.0.1_1111_Sniffer),and sniffer connection data,the sniffer.exe often automatically quit.
the sniffer pcb is not nordic.
anormal...
Hi,
Instead of initiating the DFU library in Android with an address is it possible to handover a existing GATT connection to a device already in DFU mode?
We have cases...
Hi,
I try to add support of dfu in our appl. In documentation I could not find info about softdevice size which should be provided in start packet. It looks like I should...
Hi,all
SDK:8.1.0 51822
S7 Edge（android V7.0）
i use the sumsung S7 Edge and the oppo R9S connect with my device,nRF Connect is often note:
GATT_CONN_TERMINATE_LOCAL_HOST...
for ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0
The preferred RAM,ROM and UUID COUNT is shown below
FLASH (rx) : ORIGIN = 0x0001B000, LENGTH = 0x25000...
Hi All
I am trying to build hex file using eclipse id on Mac. everything looks ok, as it eclipse build file without any error but its not working on nrf52 dk.
before...
Now I’m using nRF51822 with S130 SoftDevice.
There are two kinds of devices which is just for scan(A) – 20EA and both scan and advertising(B) - 2EA.
I found that B just...
Hi,
My question is similar to this devzone.nordicsemi.com/.../ but I can't get it to work.
I am using SEGGER_RTT_WriteString and sprintf for debugging, but I am not able...
Our mobile app is currently running atop of easyble and nordicble.js/Cordova. This library works great on all Apple devices, however, Bonding with Android devices of various...
We have done a custom PCB believing that we could use P0.0 as analog input. Now we kind of found out that we cannot, and will change the PCB design. Given that we already...
Hi, I am using nrf24l01+ tranceiver in a project I am willing to sell. I use modules with external antenna and without it. I need the CE certification of the module. Where...
