Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hello im trying to send data to mobile application, im using the example on ble_peripheral/ble_app_uart but when i compile the folowing error apears.
inking target: _build...
While writing our nRF5 based application, we have used an app_config.h in our project. This is advised as one of the solutions for updating the configuration of the SDK in...
I am a college engineering student. I currently have the NRF51 Bluetooth beacon along with the dongle I am in need of help uploading my code to the beacon via the dongle....
I have just bought an nRF51 Dongle and want to use it like a normal USB Bluetooth Adapter for my Windows 8.1. I have read the Getting Started Documentation, but there are...
I am struggling measuring time between two events. I thought to use the timer driver and the nrf_drv_timer_capture_get function and start/stop the timer with nrf_drv_timer_enable...
Dear Nordic,
I am try to implement RTC(nrf calendar implementation) in BLE example(SDK 13.0). both are working independently fine but combination of works fails RTC when...
My nrf51 SDK version is like this, nrf51 9.0 softdevice 130 chip:nrf51822_xxAArun ble_central_and_peripheral connectivity example, The nrf51 board is controlled by host MCU...
Hi All, the I/O mapping is correct as per the Ref Eval schematics. We are using a J-Link programmer to program it. The IC is not being detected in NRFgo studio. Can anybody...
Hi,
I was wondering if there is some documentation relating to pairing and bonding.
What BLE events (BLE_GAP_EVT, ???) are to be expected?
What do we need to observe...
I use ble_app_uart（sdk 14.2） + light_switch（mesh1.0.1）
Questions are as follows:
1client + 1server is ok, but in the second server there will be network failure!
log...
Hi,
I'm trying to get the tftp example working from the sdk iot examples. When I try it out following these instructions ( http://infocenter.nordicsemi.com/topic/com.nordic...
Hello,
i'm using the BLE Nano v2 with the nrf52832 on it and a DAPLink USB-Dongle. IDE is Eclipse with gcc and SDK v14.2. My current aim is to do an OTA DFU so I tried the...
I have a custom board, that basically consists of a nrf52832 module (ebyte), a button and a LED. The LED is connected as in pca10040: VDD->220R->LED-> ground to p17.
I assume...
Hi, I'm attempting to run the Proximity example ("ble_app_proximity_pca10028_s130") on my nRF51822 dev kit using the S130 SoftDevice. I am able to connect to the dev kit ...
