hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Our beacons are going into production, and to make function tests faster for our manufacturer we would like to transmit our beacon UUID, major, minor at a rate of 760ms for...
Just a question out of interest.
Is it possible to prevent the HFCLOCK from waking up on events and execute software on the LFCLOCK. I think this would be really useful...
Hi, I'm trying to create subfolders with loop. My partly code looks like:
So, it creates new dir but after that my app is crashing and rebooting, and it works fine if...
Hi, I have been running into some problems with the serial secure bootloader example in the SDKv13.1.
I build the example project from the SDK v13.1 with a custom generated...
Hi, I'm new to the nRF52840 PDK and using it for some evaluation purpose for a specific product.
Would you mind telling me how to debug the board? Is it just plug in the...
Hello,
I am developing a new application for Asset Tracking, whose general architecture is the common one - where Beacons are mounted on asset and the Reader scan for Advertisement...
Hello Everyone,
I am working on nRF52832 based custom board and testing the BLE advertising and connection with custom board, custom board adverting but when I am going...
Hi, Nordic staff.
I'm working with Central device using S120.
Our custom has developed a peripheral device using third party's BLE module and
wants the Central device...
I am trying to initialize the BLE NUS UART service and the BLE LBS service so both can be used at the same time in a single nRF52 application. I can initialize a single service...
Hey,
I was reading about nRF5 IoT SDK and it all looks amazing, I am really shocked. There is only one bottleneck I can see right now and I am not sure if there are any...
nRF_log_1.8.1.txt Hello Nordic Support Team,
We are trying to run the OTA DFU on the nRF51 device via the nRF Connect iOS application V1.7.5.
The DFU Device is available...
Hi,
I'm trying to evaluate the IAR simulator, and I'm using it w/ nRF52 samples. Besides getting errors due to the errata and system init, I'm not sure what are the use...
Hello, I was wondering if it was possible to simulate the nRF52 board using the simulator in Keil. I am trying to use it as a SPI master and it would help to be able to simulate...
In our application we use gazell. We also want to use the flash data storage which uses softdevice.
With gazell enabled, we cannot access flash.
What is the recommended...
