We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
I'm totally new to Nordic solutions. I was programming a lot in assembler in 8051 era 20 years ago. Now I feel lost in that new solutions.
I have PCA10040. It is connected...
Hi everybody
I'm working on an application where I want to sample microphone data with the adc (NRF52 DK board, nRF52832) and send it over BLE to a central device. I've...
Hello, we just made a raw board with the MDBT40, which use a nrf51422 chip. I downloaded SDK version v12.3.0 (which supports nrf51) on the nordic website. With nrfGoStudio...
Hello, I am trying to use the 'nrf51-pwm-library ' on mBed with a nrf51822 on RedBearLab Nano.
I copied the nrf_pwm.h/c files and they compile, but I never get any sort...
Hello everybody ! Designing with the development board nRF52832 and SDK14.2.
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the...
Hi
in pcb designing of the nrf52832 we use two oscillators one is 32 MHz and another one is 32 kHz.
can't we use both 32 kHz instead of one 32 MHz for saving power consumption...
I write the code base the nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart
I add some button and led function in it.
and add weight measure mode with HX711,...
Hello World...
I wanna share with my new progress to implement machine learning for nRF51822. Here it is how to make it possible. after questioning to forum that using machine...
hi,
I want to know why app_timer and nrf_drv_timer conflict。App_timer is used to broadcast data。When App_timer time out ,timer1 start.
Cannot broadcast data after initializing...
Hello everyone,
I generate an interruption when an rising edge is detected on one of my I/O.
It seems that the interruption doesn't trigger correctly for an input frequency...
Hi,
(SDK 14.2, S140 V5.0-2.alpha)
I'm working on a ble project that includes to verify mac addresses.
For the Bluetooth SIG specs, when a device has a public adress...
I just update my sdk to 15.0.0, which use the softdevice s132_nrf_6.0.0. but when I try to generate the application package, I found the nrfutil do not give the sd-req code...
Hi,
Where the Firmware is being stored in the flash??
In which address of the flash the firmware is being stored when i flash the code??
In what file type ,the firmware...
Hi.
I am trying to set up a simple Ble beacon on a PCA10040 and a sniffer on another PCA10040.
IDE = Segger Embedded Studio for ARM (This works fine)
The beacon uses...
