Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi there!
Device: nRF52 DK
App: nRF connect
Compiler/IDE: Segger Embedded studio
SDK version: 14.2
Soft device: s132
Problem description: I am trying to run blood...
Hi,
I am reading a BMX055 via I2C which consists of three sensors with three addresses.
I got the easyDMA running to read 10 times the gyro using the PPI and the data...
Hello,
my first question is about TX carrier frequency accuracy measurement. The equation given in the whtie papers is
(|f_measured - f_programmed|) / f_programmed <=...
Why is the event length of the BLE Central HRS demo set to such a high value of 320*1.25ms = 400ms?
The demo seems to work ok with the BLE Peripheral HRS demo using the...
Does the Battery Service Client (ble_bas_c) module handle subscribing to notifications from multiple slaves? In my use case, I have the nRF52840 dev kit connecting to multiple...
I need to keep track of time on a device featuring the nRF52 and have an RTC run continuously in the background. The drift should not be more than a few seconds over a year...
Hello I try to use P0.09 as GPIO with this simple code but not working. (Works well with pin P0.08)
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include...
Hello,
I use the bootloader from the SDK SoftDevice 14.0.0.
I use the Laird module BL652 which have a nRF52832 component without external clock.
To compile the bootloader...
Hello Everyone,
I am working on nRF5 14.1.0 SDK, My question is how to generate "ble_app_buttonless_dfu_without_bonds_s132.zip" dfu file.
Can any one tell me the exact...
I am using nrf52832_xxaa and SDK 14.2.0.
Does app timer play a role in power optimization?
If yes, Can reducing the app_timer frequency reduce the power consumed by the...
Is there a BLE mesh SDK for nRF52840, and if yes is there anybody tested it? I'm going to switch to the nRF52840 from nRF52832 and it is very important for me to know it is...
Fanstel BT832 module mesh client stuck in nrf_mesh_sdk.c, 187, Initializing softdevice. When I upload the code on the NRF52 DK It works, but when I upload with segger embedded...
I have set up an environment to upload data to the nrfcloud using nrfconnect and the nrf52 dk.I can only upload data upto ff and then it resets to zero .The value which i...
Hello,
I`m searching for a possibility to detect a possible Flash corruption caused by a Brown out or something else? Is there any controller interal possibility to detect...
