I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
The default I2C address of my sensor is 0x29 (7-bit).
If the least significant bit is low (0x52) the message is a master write to the slave. If the lsb is set (0x53) then...
I'm using SDK 12.2.0 with softdevice S130 V2.0.1 and want to use TWI.
Using the ble_beacon example I added the twi code from twi_sensor.
Shortly after calling TWI_Init(...
Hi,
during normal operation, my device shows a power consumption of 4.7mA.
Normal operation is:
accelerometer (lis2dh) detects a shake and wakes up the nrf51 via...
Hii ,
i am using customized board (chip : BT832).
err_code = sd_softdevice_enable(clock_source, softdevice_assertion_handler); hangs. it took some delay and after that...
Hi all,
I have seen a pair of questions ( this and this ) that I think have something to do with this, but didn't find a solution.
I have a custom board with a button...
I want to have an application similar to UART in the SDK example, with multiple peripherals.
I tried to modified existing UART example, but cannot make the central node...
I want to add the nrf52832 to my customized board and I am studing the possibilities for flashing it once that is located on the board. Is it possible to flash trhough the...
I have a board with some LEDs that are driven in the same way as with the nRF51 DK board (i.e. there is a resistor in series with the LED and you drive the pin low to turn...
In our testing we encounter some devices (Centrals with nrf52832), where the peer manager event PM_EVT_BONDED_PEER_CONNECTED contains a invalid peer id 0x4000 (allowed values...
I have a device the uses MSP430f169 and CC2500 RF controller for communication I need to replace the CC2500 RF controller with nRF51422 device.
As I understand an nRF51422...
Hi,
I develop application on MBED platform with NRF52-DK. I figure out that pin "logic" on this board is interchanged. For example. I have LED connected to some pin. When...
Hello,
on my custom board I am trying to use pin P0.09 and P0.010 for interrupt-purposes. So I integrated the necessary adjustments as mentioned in this topic here , which...
Hi,
I develop application using BLE.
In my scenario two NRF52832 operate in two different roles (Client and Server).
I have ready to run app (as server) and can communicate...
Hi,
When I call nrf_drv_spi_transfer to transfer 250 bytes in non-blocking mode, it takes 1.1ms. Is this normal? Any workaround? If it is normal then I have to split my...
My android app give me this "register with gatt stack failed" error on Samsung S7 marshmallow. The scenario is that I am working with 21 BLE peripherals (nrf52). I scan available...
