Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Nordic Team,
We are using Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v3.0 to sniff packets from BLE 4.0 device - but we are finding it hard to connect...
Hello ,
i use blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. I want to flash the led with periods (period of 30 ms turn on 10 ms off) ...
Hi,
I'm using 52810 basing on ble_app_uart example. We use a IO to start or stop advertising. Start advertising w hen the IO level is low while stop advertising w hen the...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I am considering using two nRF52832 or nRF51822 's for a project which requires two way BLE communication. Pressing a button on one end should cause an event on the other...
Hello, I have an adafruit bluefruit feather m0 which has nRF51822 on it, I was able to establish a connection and send data until yesterday. When I try to find my adafruit...
Hi All,
I have a general question about the FreeRTOS implementation for SDK 14.0.0.
I've added FreeRTOS onto a basic UART BLE peripheral example that I wrote. I referenced...
Hey Guys,
I'm trying to import an existing Keil project into Segger Embedded, SDK 12.3.0.
I know this link exists which explains importing prior to SDK 14.2.0. However...
In the PS v1.4 pages 13-15 related to the QFN package.
Pins 11, 12 (P0.09, P0.10) are marked with the note '1'.
On page 15, at the bottom, the notes are enumerated:
...
I have a button that will put my device into pairing mode. While in this mode, I want central devices that connect to form bonds so that when not in pairing mode I have a...
Here I document how, in Eclipse, to start two, concurrent debugging sessions to two NRF5DK boards (or other debugging probes) , connected to different USB ports of the same...
Hello everybody,
I have problems with selectivity when I scan. There are 5 peripheral devices with different " DEVICE_NAME " but the same UUID and type (same " ble_uuid_t...