Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello, I would like to get data from the advertising packet. I think that utilize this function is a good starting point :
Then ... For exemple, what do I need to do to...
HI ,All
I want to update the data at the same address in nrf52832 flash. What should I do? Do you have an example program? If you have, please send me a copy
Thanks...
Hi, I am designing a central using nRF51422, SDK V11, S130V2.0.0, modifying the central example to connect to a Ammicom BLE module of a product. After the CONNECT_REQ is sent...
Will the nRF52840 eventually support SPI speeds greater than 8 MHz? Will a preview / reference board for the nRF52840 be released with support for these higher SPI speeds...
Hi,
I am trying to set up a slave select on P0.28 but I noticed it's not driving high. I've tried several settings and I'm now using the example from https://devzone.nordicsemi...
Hi,
I am working on NRF52840 soc with SDK 15.0. I am trying to advertise beacon adv to long range. But i got to know that non connectable long range Advertisement not possible...
Dear Nordic Team,
Thanks for supporting.
hardware : PCA10028 (DK 51)
Software : SDK12.3.0 ( NUS example )
Secure DFu implement with NUS example it is compiled and...
I developed one project using BMD-300 Evaluation Kit that include nrf52832 microcontroller. In my project, I use the nRF5_SDK_14.2.0_17b948a and s132_nrf52_5.0.0_softdevice...
Hi everyone,
Using the SDK11.0.0 development product, it was found that the 52832 restarted randomly, with a reboot time of 7 days or longer.
App code condition:
1....
Hi guys!
First of all, sorry to make this question here because it is almost unrelated to Nordic, but I am desperate. I developed a device using your nRF52832. I programmed...
Hi,
I have a problem with Thread network stabilty and formation in new SDK for Thread and Zigbee 1.0. Examples seems to work fine in unchanged form, network is stable and...
Repetition of the steps followed here.
(1) Generated priv key, and public_key.c file using nrfutil, (2) generated the bootloader_settings file using nrfutil (3) Compiled...
hi!
nordic team
i am using thingy 52,and i meet a question that app_thingy_s132.axf: Error: L6405E: No .ANY selector matches accel_auto_cal.o(.bss) when i compile this...
Hello,
I am using nrf51822 with sdk11.0.0.
i observe that in while loop sd_app_evt_wait() function take much time for next interrupt to be pick.
is there any alternate...
