I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello guys I am using nrf52840 interfacing analog sensors like potentiometer and accelerometer. This is not related to nrf, but I want to design a simple ADC filter that I...
Using a clean mesh sdk 3.2.0, I created a build directory inside the folder where I extracted the mesh sdk to.
Then, inside that directory, I used CMAKE with the following...
Hello,
I am currently developing a product using the nRF9160. I would like to use concurrently GPS and LTE-M.
I send periodically data to my server using LTE-M network...
Hello,
In the documentation on Infocenter for nRF52840 it is recommended to use P1.01 and P1.02 as low-frequency GPIO, while on nRF52840 DK those PINs are used for UART...
We would like to use Wifi (2.4 GHz) and BLE in the same device. The current design will have the BLE Module Rigado BMD-340 and the Wifi Module Microchip WINC1500.
https...
Hi there,
I have added my custom services in the peripheral dfu_template example.In the advertising UUID array(m_adv_uuids),i included custom service UUID but not the...
A question about the power saving modes PSM and eDRX. A device is mostly in deep sleep and wakes up cyclically for mobile communication. It is better: Completely disconnect...
In our project, two nRF51840 will communication with each other using BLE. One nRF51840 act as central and another nRF51840 with act as peripheral. The central nRF51840 will...
I have a couple of NRF51 parts. They're pretty common at hobbyist stores still. Recently I pulled out the NRF51 dongle, downloaded the recommended Segger Embedded Studio,...
I have managed to get working a BMW iDrive to act as a bluetooth mouse for my iPhone. To do this I used a CANBUS shield connected to an arduino NANO and an nRF51 BLE connected...
Hello,
Mesh SDK 4.0.0, PCA10040 x2
I want to develop next models:
Scan server: Waiting GET message with arguments, scan BLE beacons and reply STATUS message with results...
Dear Nordic Team:
Now I am doing a example test, with nRF52832 I want to use SPI master and SPI slave transtission.I have saw many demo example,but i dont know that which...
I don't know how it feels if you visit a page that takes six seconds to open.
Isn't the profit ability of the Chinese region enough to allow you to build a normal acceleration...
Hello,
I am working on nRF52832 chip using SDK 15.3.0 in segger embedded studio.
I implemented DFU in my application and it's working properly.
But my problem is when...
