I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
It is possible to provision the NetKey, AppKey and unicast address of a node using the serial protocol, using the following messages:
Mesh Subnet Add, Opcode: 0x92 - NetKey...
Dear Sir or Madam,
It´s the second time, I got the same error while start developing with nrf52833 demo board. For first step, I flashed a blinky example to the board -...
Now I'm trying to change a device name in `nrf_dfu_ble.c`. I set NRF_DFU_BLE_ADV_NAME like following.
And I imported `stdio.h`, `string.h`. And I edited `gap_params_init...
Hi,
im trying to flash a 3rd party demo board (MDBT50Q-512K Module Demo Board) with nrf connect for desktop. As programmer I use original Segger j-link edu mini.
As...
Dear Nordic:
My peripheral is configured to use MTU 247.
When connected by NrfConnect of IOS, I can receive NRF_BLE_GATT_EVT_ATT_MTU_UPDATED event and check the effecitve...
We are designing in the 52840 as a processor in a new sensor product and are looking at using the HOLYIOT YJ-18010-nRF52840 part that you indicate on your site is a third...
Env setup:
nrf52840 on PCA10056, SDK 16.0.0, S140, FreeRTOS, secure bootloader
Description:
I'm trying BLE background DFU in the application.
Had reference iot/background...
Hi
Is there any implementatiaon of nrfutil, and more specifically the DFU via serial port, as a C library? My use-case is I need to update an nRF52840 from within an already...
Hi,
I am able to set up uart async receive, but when I try to set the call back using uart_callback_set() so that i can call the uart_tx() routine to push the data out,...
Hello,
I am working on nRF9160DK. I am using SES for ARM (Nordic edition).
How can I import new libraries for any project? Let's say I want to import SD card libraries...
Hi!
A little backstory on my project: Currently I have merged the saadc and peripheral ble_app_uart example. The value from a potentiometer is then sent over ble to the...
Hi,
I'm developing a project with nrf52832 sdk 16.0.0. I have some issue about the fds. peer_manager had used the fds modul, as we knew. And I would call fds_record_write...
I am looking at the APP_ERROR_CHECK and find out it finally goes to the app_error_save_and_stop method. I couldn't understand from the code, that where the error info saved...