I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am currently working on a low power application using the NRF9160 chip. During power optimalisation I found out that my sleep current can be reduced from around 50uA to...
Hi, following the IOS-nRF-MESH-Libary examples. Using Segger Embedded Studio
Using Segger Embedded Studio 4.42, Tools, Options, Environment Options, Global Macros
SDK_ROOT...
Hi
I am trying to implement a lightweight algorithm on nRF52832 Development Kit. When I try to debug the code, it shows "unknown function at address "0x00000A60". I am attaching...
Hello,
I can successfully compile projects based on nRF52832 and nRF52840. Whenever I try to compile an nRF52811, even the projects in the examples folder, my IDE prompts...
Hi,
I wanted to test the NFC on nRF52840 DK. I have seen that to test NFC we need a Adafruit PN532 NFC Shield. Why cant we use 2 DK's with NFC antenna to test NFC. I have...
I tried the following code:
In main:
void sys_dispatch_handler(uint32_t sys_evt, void * p_context) { test(sys_evt); }
And registered the handler as follows:
NRF_SDH_ANT_OBSERVER...
Hi Nordic,
I build the nRF UART 2.0 application source code running on Android OS 5.1 and it works well, but android 10 cannot scan the device.
I migrated to Androidx...
Hi,
Some questions regarding passkey and Diffie Hellman.
When a device connects to a mobile - the mobile user should insert a passkey.
Does this passkey used as a...
Hi I am developing a Multi-link Central that connect to a mobile phone and multiple BLE dongles. I use the Multi-link and BLE blinky in SDK 17, it works fine.
My problem...
Hi all,
I tested with example uart_pac10056 (SDK16), but return error NRF_BREAKPOINT_COND.
When i debug, it show error in APP_UART_FIFO_ERROR.
Could you show my mistake...
Hi All,
Is it possible for me to broadcast multiple&different type of beacons/advertisement, for example ibeacon, eddystone, unconnectable-advertisement, connectable-advertisement...
Hello, I would like to use the pc_ble_driver_py with sd api v6. I can see in the CMakeLists.txt where I can change set(SD_API_VERS "2;5") to set(SD_API_VERS "2;6"), and it...
Application Info:
I am working on developing a synchronized mesh network of low power sensors. I am trying to maintain an average power consumption of 100's of µW while...
