Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Dear NRF community and support This is a followup question to the DevZone post https://devzone.nordicsemi.com/f/nordic-q-a/2860/flashing-bootloader-and-application-via-j-link...
From everything I know and understand of the system architecture, this shouldn't be possible, but one of our early production units out in the fields has twice now apparently...
I'm designing a two-part computer input device: Part A will communicate with the computer over BLE, but it must also be able to forward along messages from Part B. Here's...
Hi,
I am trying to update the MTU between the central and peripheral to the maximum MTU.
at the connection interrupt from the central side I added
but I got error...
For nRF52832 I see in the datasheet:
I OFF_RAMOFF_GPIO System OFF, No RAM retention, Wake on GPIO,
While for nRF52840 only “System OFF, no RAM retention, wake on reset...
I have an iOS App which is just designed for updating our device firmware OTA. It uses the Nordic DFU library, updated to the latest cocoapod. It connects to our device, and...
Hi,
I use OpenWRT and nRF52832 to develop a BLE gateway, the nRF52832 connected to OenWRT through UART. Now,we need the uart serial DFU of nRF52832, and I found that nrfutil...
I am looking for some advice before diving in to what could be a big waste of time. In my existing Thread implementation, I use nRF52840's in two different configurations...
Hi all!
I am using mesh sdk v4.10 and sdk 16.0 with an nrf52840 custom hardware. I have a question regarding the mesh event handler. I am seeing something weird which I...
I am trying to run DHT sensor on the nrf9160 using the sample provided by zephyr (can be found under zephyr>samples>sensor>dht). The code was meant to run on nrf52. Is there...
hello everyone,
I'm using SDK15.2 in nrf52832. I need to update my sensors value(Temperature, Humidity and accelerometer) data to advertising non connectable beacon. How...
Hi,
I'm using nRF52832 board and I'm modifying the Eddystone BLE Application in ble_peripheral example in SDK 16.0.0. I'm trying to get the characteristic value of ADV Advertising...
Hello, we are creating a nordic peripheral using an nrf52832 and SoftdDevice S112 and SDK 16.0. We need to store quite a bit of data non-volatilely, at a fairly fast rate...
hi
im use nrf52840 as a gazell device which run the demo \nRF5_SDK_16.0.0_98a08e2\examples\proprietary_rf\gzll\gzp_desktop_emulator\pca10056 ,and use nrf24lu1p
(\nrfready_desktop_2_v3...
