I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hello,
I want to transfer data from nRF52840DK to nRF9160DK using SPI. I want to use nRF52840DK as master which will transfer the data and nRF9160DK as slave which will...
Hello,
What happens with the LPN firmware if it currently has an IV index of 0 and loses power for an extended period of time. When it gets power, the network that it is...
Dear All,
I am using the example UART in Peripherals
I can send data easily but have problem in receiving data. When I try to receive data the UART Fifo Event handler...
I looked through the example projects provided in the nRF5 SDK for Mesh, and the only models ever used are generic on/off or generic level. Do you guys have an example which...
Hi,
Sorry for the seemingly simple question. I'm using the nRF52832 chip and I have a 4xdip switch connected to P26, P27, P09/NFC1 and P10/NFC2. I can successfully read...
Hello,
I recently updated the asset tracker on my thingy 91 with the lastet available pre build firmware (2019-11-29_d3130d77) using MCUBoot.
Since my Thingy91 is only...
I started with the mqtt_simple example.
I added:
#CONFIG_MQTT_PASSWORD="pass" #CONFIG_MQTT_USERNAME="David"
to the prj.conf file. Relaunched the project which rebuild...
As a matter of fact that there is no special EEPROM in nrf52832 , the user data which need to be stored in nrf52832 should be written into the flash of nrf52832 . The SDK...
When debuging nrf52832 , the code can be flashed into the flash through JTAG . However , I need to reprogramme the nrf52832 through UART interface . It seems that there is...
Hello.. I use RNF52840 Dongle. I compiled the blink example with VS code and I programmed with nRF Connect tool.
now I can't connect the USB device. I read that I had to...
Hello,
I am currently aiming to create an application for the nRF52-DK using the nRF5 SDK and Segger Embedded Studio as my IDE.
Due to the SDK itself being extremely extensive...
Hello ,
I have been trying the Zigbee CLI light example.
And I modifed the main.c file to have the network saved "ZB_FALSE" and then flashed the updated hex file to 52840...
Hi we are having issues with gpiote interrupt. We would like to do some spi read when drdy gpio becomes high to low. I have done above configuration for the same.
We are...
I have a problem collating model publish events arriving at two different nodes in my mesh.
My application is an array of sensors publishing through generic on off and generic...
Hi,
I have a custom board running NUS peripheral which uses the nRF52832 and a NUS central which is running on a nRF52 DK. I modified the ble_app_hrs_freertos example to...
