I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi,
I am using RTT log with nRF52832, my question is when debug port is disconnected, what will happen to RTT logger?
Will they be simply ignored? or will the debug pins...
Hi.
I want to measure the current on the nrf 52840. I have downloaded the beacon example on the board and I want to measure current when the beacon is transmitting(LED 1...
Hi,
I am developing an application using BMaD 300 Eval board nrf52. As a first I want to display device information along with MAC address of BMD 300 I have, in advertising...
Hi,
I loaded bootloader, SoftDevice, and Application using nRFConnect - Programmer. But it doesn't launch the application. It fails at
nrf_bootloader_fw_activate() with...
Hello,
I want to read the values from MPU9250 magnetometer i.e. from AK8963 I wrote a function just like accelerometer and gyroscope shown below:
uint32_t mpu_read_mag...
Hi!
I'm looking for a new Bluetooth module for a controller, and I run across the nRF51. I used to have a module that I controlled from the MCU, but this SoC looks like...
I am trying to use the NRF_LOG system with FreeRTOS. In the case of an ASSERT, I want to be able to:
1) log the location of the assertion
2) flush the logs over RTT
...
I’m using the library pc_ble_driver_py last release 0.14.1, and Nordic DevKit PCA10040. My goal is to set the central IRK value and generate a private resolvable address....
Hi, i am trying to build a ble beacon for personal asset tracking. The one that is like Tile or Trackr. What kind of chipset and program that i should use.
Hello
P airing: Just Works with Bonding: Passkey Entry, Peripheral Displays works for bonding.
I want to make LESC Pairing: Just Works with Bonding. Is it possible? According...
I got a vague "cmake did not complete" error from studio when the sdk was installed at a hgfs mounted disk. It worked ok when the sdl was installed at non-mounted directory...
the gy-80 module which has
1. HMC5883L
2. BMP-085
3. L3G4200D
4.ADXL345
i want to get the x, y, z axis of the sensor's position
which example i have to use and...
I am building a project with CMake, inside nRF SDK for Mesh 3.2.0, which uses the math library:
1. source file includes math.h
2. CMakeLists.txt adds m to target_link_libraries...
There are a lot of missing materials under the topic:
Software Development Kit > Previous versions of nRF5 SDK for Thread and Zigbee > nRF5 SDK for Thread and Zigbee v3...
I'm converting an already working LPN that went into SystemOFF with GPIO wakeup for lowest power consumption.
Now I want to use the RTC2 as a secondary wakeup.
I know...
