Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello,
I desperatly try to implement a bootloader with the s310 softdevice. When I received the data to be written (via BLE), I erase the flash:
std::uint32_t rc = NRF_ERROR_BUSY;...
Hi,
When will the user guide be available? I have the PCA10040 V0.9.0 2015.39 PCBA that I got from the Global Tour. I am using the nRF51 Development Kit User Guide v1.0...
I try to build example projects in 32k limit Keil uVision. I'm not able to build some of the projects (e.g. Heart Rate Service) because of the 32k limit for the compiler....
Hi Nordic developers,
I'm using TWI software driver provided by NORDIC.
I need to have 400 kbps frequancy.
I have seted TWI_DELAY() to 0 and TWI_MASTER_TIMEOUT_COUNTER_LOAD_VALUE...
I'm an Android developer and I bought the NRF51822-Beacon kit. All I want to do is be able to "see" the beacon using Android's onLeScan() bluetooth call. However, the beacon...
Hi people!
We are having an issue with our custom PCBs using the nRF51822. They are programmed and debugged using a custom external test board, using the SEGGER J-link...
Dear developers;
I am aware of the fact, that the nRF51 S110 softdevice (supports concurrent Peripheral and Broadcaster role) does not support connections to multiple Central...
Hi, do you guys have any recommended parts for transmitting audio through Bluetooth? I would also like something that is compatible with iOS and Android if possible. Thanks...
Hello,
I know that similar questions have been asked before, but I am trying to schedule a number of 2 or 3 different advertising messages that I want to broadcast one...
I have a Jayconsystems breakout board for the nrf8002 bluetooth chip. Nothing is connected to the breakout board and the chip is unprogrammed. My current meter reads 6.0 mA...
Hello,
I want to make my Arduino coupled with the nrf8001 advertising a simple data (an integer). There should also be a possibility for dynamically changing the advertising...
Hello,
I was trying to compile a BLE proximity project with Keil nRF52 SDK, but got error such as struct "" has no field. I can command out all these error and compile...
Hi,
in order to find out how Android nRFToolbox App works, I downloaded Source Code on:
https://github.com/NordicSemiconductor/Android-nRF-Toolbox/releases
I unzipped...
Hi,
I am using nrf_gpio_port_read to read port 1 (pins 8-15), and I want to know how long it takes to read the port, ie. how many instructions. I am doing this in an interrupt...
