Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello:
Does the nrf52 radio peripheral EasyDMA write to PACKETPTR on byte boundaries or does it write "bits"? Suppose I have the ADDRESS_BCSTART shortcut enabled and the...
Hi all,
I can use the API sd_ble_gap_rssi_start to start RSSI and can get the value when the BLE_GAP_EVT_RSSI_CHANGED event occurs.However,when I use the sd_ble_gap_rssi_stop...
Hi, I'm recently concerned with the latent risk that nrf51822 might be hacked by extracting the firmware also known as "snarf"ing.
And I know there is Memory Proection Unit...
I followed the guide of github.com/.../nRF51-ble-bcast-mesh to try the mesh with NRF51822.But there seem no discribtion about which softdevice we should use.I loaded the s110_nrf51822_7...
Use SDK6.1 / SD7.0, iOS9 can not pairing!
dm_ble_evt_handler() return error "BLE_GAP_SEC_STATUS_UNSPECIFIED"!
It is the captured packets file: ble_proximity_ios9.1.pcapng...
I can't find an implementation for the indoor positioning service in any of the SDKs. Should I assume it's not implemented? If so, are there any plans to implement it?
...
Hello,
a presentation given at the nRF52 Global Tech Tour stated that one of the planned features for S132 and S130 was a support for multiple peripheral connections (2...
Hi
Now I'm using the S130 and ble_app_uart.I meet some problem need your help.
Firstly,I download the code to PCA10028,then it can connect to nRF UART on the iPhone5S...
Hey,
I am a bit confused with "client characteristic configuration" that is used to enable notifications (at least in Android).
To enable the notifications I have to...
The manual for my Agilent N4010A Wireless Test Set talks about a BER test based on a "vendor specific loopback test mode". This mode would allow me to do BER measurements...
Hi there,
I am starting with nrf52 and SDK 9.0.2 and am struggling with the SDK structure.
Can anyone please explain the difference between
components/libraries/uart...
Hello, I have tried to combine saadc with softdevice, but having errors during compiling. I have copied .c and .h files from saadc example to ble_hrs example, but having following...
Hi,
I have a specific application/product where in I am planning to use Nordic nRF52832.
-> There is a 9 Axis Inertial Measurement Unit (accel/gyro/magnetometer) connected...
Hi!
I have been trying for over a year to figure this out, but I am unable to, and I would hope it be pretty straight forward since OTA is already in the Nordit Master Control...
