Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello.
I am trying to port BLE serialization code to a host MCU, to say STM32F4.
I am looking through porting documentation (BTW, it is quite well documented. Well done...
According to Microsoft's instruction on HID touch device, msdn.microsoft.com/.../dn672271(v=vs.85).aspx , a HID touch device should create a report (descriptor) as below,...
Hi,
I am having a 324 byte,a 420 bytes of array stored in flash,now i am updating these array with 360 bytes. in fds_event_handler in the case FDS_EVT_WRITE i am reading...
Hi,
I'm looking for an example which combines FreeRTOS, BLE and ADC on nrf52 board(10040).
I'm able to have FreeRTOS with BLE, FreeRTOS with ADC but not everything together...
Hi,
I've read a lot of question on the forum, but I'm a lit bit confused about what I have to do to use one static passkey on the central and peripherical device. In my...
Hi There,
I'm having problems with my hardware timer appearing to stop counting or not being cleared via a short when the timer interrupt is executing.
In my application...
Hey!
I want to use the nrf51 BLE-module in some special environment.
It should be able to work with bluetooth and in addition to it with some other RF protocol (Gazell...
Hi,
I have added "DFU" functionality to my existing BLE application Test.rar .
"I am using nrf52 SDK v11.0".
I have programmed the device with softdevices (S132.hex...
Hi,
I am new to eclipse on windows.
I have bought the PCA10040 board.
I have installed eclipse and GNU ARM Eclipse 3.1.1 plug-ins.
Copied the NRF52-SDK into workspace...
Hi developers,
I am trying to collect data from an AFE (ADS1298) and could get some values. Inorder to check the accuracy I need to plot this value. I am programming this...
Hi,
I am running the nRF51822 from a coin-cell. I need to measure the cell voltage. Until now, I have attached VDD to an ADC pin with a voltage divider and a capacitor...
Hello~
In my production line use jig contact my PCBA, and use Jlink connect to Nordic 51822 download FW, but I found sometime can use 500kHz and sometime can't use, just...
Hi
I am using nRF52(PCA10040) as a sniffer dongle, but it seems the sniffer mode cannot work, and shows the error log: "INFO: Error on port xx. file: Packet.py, line 245...
