Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
I'm using the MAX9814 electret pre-amp's output as an input to an analog pin of the nRF51822. The MAX9814 has a 1.2V swing at 1.2V DC (so it goes from 0 to 2.4V). VDD for...
Hello,
I have some questions about the DC/DC conversion factor in nRF51822.
In the datasheet nRF51822_PS v3.1, Figure 11 shows the graph about conversion factor...
I would like to change the device name of the nRF51422 trough a mobile device(Android AND iOS ). The name should be stored even when I disconnect the supply.
From a nordic...
Sir,
We designed a prototype card including "rfd22301" containing nrf51822. We will use in mass production directly the nrf51822.
We will use the BT as a transparent UART...
Hi, I try to transmit mp3 or wave file.
and I am using nrf51822. Is it possible?
I know that people usually use the A2DP profile, When they send a music or video
...
I'm running example apps from the SDK on a PCA10028. When debugging in Keil uVision, I find that I can only stop the code once. The second time I try to stop the code I always...
Hey All,
I am working on a project that involves a Redbear Labs Blend as a sensor platform, then transmits the data to a dfrobot Bluno over nRF8001 BLE. I'm still new to...
The release notes for S110 v 8.0.0 say .
The SoftDevice Specification corresponding to this release is the
S110 SoftDevice Specification v2.0.
I can't find...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, I am using nRF51822 to generate two channels PWM to control motors. Softdevice is V5.2.1. But I found the the Blue tooth connection sometimes dead if the PWM frequency...
I would like to create a unit which is intermitting in the master and in the slave role.It should be most of the time "advertising" and waiting for some master to connect...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi all, please I have some questions.
1- When adding a service then a characteristic, this enables the SoftDevice to send BLE events to the application whenever a client...
