I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi ,
I am using nRF51 SDK with S130 soft device lib, and it is running well when downloading the example of ble_app_uart. But when I want to modify the service UUID from...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
Hi,
The situation: nRF51 has established a connection with the iOS/Android (custom made)App. The nRF51 goes out of the Bluetooth range. Eventually, the Bluetooth connection...
I have looked around but have been unable to find doc explaining this. If there's something around, I'd truly appreciate a pointer.
I have an existing (solar powered) device...
Hello,
i'm searching for informations about calibrating the SAADC of the nRF52. And i have read here: Link
For nRF52, there are no calibration
values that I know of...
Hi Sir/Madam
I wrote a small program for low current verification on nrf51822 development kit with starter mother board.
The program is based on "blinky_example" project...
Hello to all,I have developed a board using the NRF51822;
Currently I am using SDK v11, S130 v2.
I have a problem in my bootloader, since bootloader_app_is_valid (from...
Hi, i want to jump from my app to the bootloader, i used the function
void bootloader_app_start(void)
{
vMBt_eStopAdv_Exe() ;// Stoping the BLE ADV
sd_power_gpregret_clr...
I have a question about when the application is erased during serial DFU single-bank update:
According to the S110 Serial HCI documentation , the serial update packets...
Hi,
I just purchased an nRF51 sniffer. I have set everything up as per the UM. When I invoke the sniffer application, it says scanning for devices, but nothing shows up....
Hello.
I'm investigating how bootloader works (bare minimum), especially how it brings control to an application (already flashed at 0x1B000, s130 SoftDevice also present...
Hi,
I'm creating a simple SPI bootloader without SD for nRF51822 based on this post
The bootloader is connected to Freescale 22F through SPI and it will be without any...
Trying to build the examples for the NRF52 and ant. I have the latest download of SDK11 (nRF5_SDK_11.0.0_89a8197)
It looks like paths are broken as well as missing the ant_interface...
Hi,
I want to communicate with other chip on UART.
the chip on other end requires AT(CR,LF) command to start communication over UART.
UART is setup correctly, but it...
