Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I am using SPI MASTER example from sdk 7.2.0 with softdevice s110(using spi along with BLE).
In my program I have a requirement of reconfiguring spi pins after using spi...
I see that driver version 1.0.0 was tagged on ghitub: github.com/.../v1.0.0
However, when I visit this page: www.nordicsemi.com/.../38649 , I can only find the 0.5.0 version...
Hi
I use nRF51422 for our products.
In a product line, we check the CWtest mode current consumption current.
I decided the determination value of the CWtest mode current...
Hi.
I'm using nRF51822, S130, SDK10.0.0.
I made a source code as below refering radio_test which is in SDK examples.
But the width of frequency is just 0.2MHz as below...
hi,
so i was coding my program with keil and it reach the 32kb so i had to move to the free IDE Eclipse. for that i followed this tutorial devzone.nordicsemi.com/.../
...
Hi !
I've seen that the Makefile given with the examples changed a lot between SDK11 and SDK12, lots of improvements ! However there's still something I don't get. Why...
What system resources are required when using GPIOTE channels (not the PORT event, the other channels)?
I remember on the nrf51822 there was a long-running PAN, fixed in...
I programmed nRF51822 with S120 softdevice and ble_app_hrs_c application to scan beacons.
It works fine but have one problem.
It scans beacons for about 10 seconds...
hi,
i am working on ble_app_uart_simple_adc example which is referred from the link github.com/.../nrf51-ADC-examples
i flashed the code successfully. and detecting the...
Running the SDK11 example \examples\peripheral\twi_sensor on a NRF52 PCA10040 version dev board and can't get any output from TWI pins. Leaving pins unconnected and using...
Hi,
I am trying to set up the development tools for the NRF52 on my Mac by following this tutorial aaroneiche.com/.../
I am getting the following error when i try to...
Hi
I want to get external acceleration sensor values with SPIM using easyDMA on the sensor interruption (using GPIOTE). then after getting all data, I want to calculate...
Hello,
I have question, I'm actually developing an Android application and try to update the firmware on a device with a DFU process. It work on every mobile device except...
I am using the nrf51422 with softdevice 5144_2.0.1 ,
I set two network number using the "sd_ant_network_address_set" api , network number 0 for ANT+ cadence/heardrate.. network...
Hello,
I was just checking for differences between SDK v11 and v12, more specifically, the differences in the SPI HAL and driver code.
In hal\nrf_spim.h of the v12 SDK...
