Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi there,
I'm using an input GPIOTE based on SDK11. The interrupt is consistently being fired. On the other hand, if I use "if(Pin_6)" to check the trigger, it does not...
I am trying to use SEGGER_RTT_printf with SDK12 in eclipse.
I have added the appropriate lines to the makefile and SEGGER_RTT_WriteString works fine.
My Makefile lines...
I followed this blog entry ( devzone.nordicsemi.com/.../) setup IAR to debug in monitor mode (by adding Jlink_monitor.c, jlink_monitor.h, jlink_monitor_isa_iar.s, add EnableMonMode...
Hi,
In our project we need to store data onto the internal flash memory.
The data that's stored will be transferred and modified via "BLE uart service". When I tried...
Hi guys,
I'm working on an nRF52832 chip (PCA 10040) with softdevice s132 (v3.0.0) and I'm facing with a big problem; in my project I use an spi (instance index 0) and an...
Hi,
we have the need to develop an application that needs a precise second counter over time.
Our firmware is using the S110 SoftDevice (v8.0.0) and SDK v8.0.0 to perform...
Hi!,
I'm trying to compile GitHub examples, for example this github.com/.../nrf51-ble-tutorial-service
I cloned it into nRF5_SDK_12.1.0_0d23e2a/examples/peripheral....
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
Hi
We are using "gcc compiler" to compiler our programs. To download our programs we use "nRFgo Studio" app.
From the above image, when we load SDK into the device...
Hello,
Consider this scenario:
The client successfully writes to a characteristic by the application code can't use the data sent so it would be usefull to signal the...
Hello,everyone. Now i have the board nrf52832 and i want it to enter the low-power mode but keep the the advertising. Now the measured current is 160uA, I think there should...
Dear All,
I apologize in advance if it seems that the question has been already posed but it is still unclear to me.
I have a pin (SIG_OK) and I want to read its logic value...
On the nRF51 DK there is a MM8130-2600 connector. I suppose it is used for connecting coax cable when tuning the antenna(?)
The connector is quite expensive, though. Is...
Per the name "UUID" and the very limited background knowledge that I have, it appears that a particular device can have its UUID assigned by its manaufacture, who bought the...
